1Gb: x4, x8, x16 DDR3 SDRAM
Mode Register 0 (MR0)
Table 76: Burst Order
Starting
Burst
Length
READ/
WRITE
Column Address Burst Type = Sequential
Burst Type = Interleaved
(A[2, 1, 0])
0 0 0
0 0 1
0 1 0
0 1 1
1 0 0
1 0 1
1 1 0
1 1 1
0 V V
1 V V
0 0 0
0 0 1
0 1 0
0 1 1
1 0 0
1 0 1
1 1 0
1 1 1
V V V
(Decimal)
(Decimal)
Notes
1, 2
1, 2
1, 2
1, 2
1, 2
1, 2
1, 2
1, 2
1, 3, 4
1, 3, 4
1
4 chop
READ
0, 1, 2, 3, Z, Z, Z, Z
1, 2, 3, 0, Z, Z, Z, Z
2, 3, 0, 1, Z, Z, Z, Z
3, 0, 1, 2, Z, Z, Z, Z
4, 5, 6, 7, Z, Z, Z, Z
5, 6, 7, 4, Z, Z, Z, Z
6, 7, 4, 5, Z, Z, Z, Z
7, 4, 5, 6, Z, Z, Z, Z
0, 1, 2, 3, X, X, X, X
4, 5, 6, 7, X, X, X, X
0, 1, 2, 3, 4, 5, 6, 7
1, 2, 3, 0, 5, 6, 7, 4
2, 3, 0, 1, 6, 7, 4, 5
3, 0, 1, 2, 7, 4, 5, 6
4, 5, 6, 7, 0, 1, 2, 3
5, 6, 7, 4, 1, 2, 3, 0
6, 7, 4, 5, 2, 3, 0, 1
7, 4, 5, 6, 3, 0, 1, 2
0, 1, 2, 3, 4, 5, 6, 7
0, 1, 2, 3, Z, Z, Z, Z
1, 0, 3, 2, Z, Z, Z, Z
2, 3, 0, 1, Z, Z, Z, Z
3, 2, 1, 0, Z, Z, Z, Z
4, 5, 6, 7, Z, Z, Z, Z
5, 4, 7, 6, Z, Z, Z, Z
6, 7, 4, 5, Z, Z, Z, Z
7, 6, 5, 4, Z, Z, Z, Z
0, 1, 2, 3, X, X, X, X
4, 5, 6, 7, X, X, X, X
0, 1, 2, 3, 4, 5, 6, 7
1, 0, 3, 2, 5, 4, 7, 6
2, 3, 0, 1, 6, 7, 4, 5
3, 2, 1, 0, 7, 6, 5, 4
4, 5, 6, 7, 0, 1, 2, 3
5, 4, 7, 6, 1, 0, 3, 2
6, 7, 4, 5, 2, 3, 0, 1
7, 6, 5, 4, 3, 2, 1, 0
0, 1, 2, 3, 4, 5, 6, 7
WRITE
READ
8
1
1
1
1
1
1
1
WRITE
1, 3
1. Internal READ and WRITE operations start at the same point in time for BC4 as they do
for BL8.
Notes:
2. Z = Data and strobe output drivers are in tri-state.
3. V = A valid logic level (0 or 1), but the respective input buffer ignores level-on input
pins.
4. X = “Don’t Care.”
DLL RESET
DLL RESET is defined by MR±[8] (see Figure 53 (page 138)). Programming MR±[8] to 1
activates the DLL RESET function. MR±[8] is self-clearing, meaning it returns to a value
of ± after the DLL RESET function has been initiated.
Anytime the DLL RESET function is initiated, CKE must be HIGH and the clock held
stable for 512 (tDLLK) clock cycles before a READ command can be issued. This is to
allow time for the internal clock to be synchronized with the external clock. Failing to
wait for synchronization to occur may result in invalid output timing specifications,
such as tDQSCK timings.
Write Recovery
WRITE recovery time is defined by MR±[11:9] (see Figure 53 (page 138)). Write recovery
values of 5, 6, 0, 8, 1±, or 12 may be used by programming MR±[11:9]. The user is re-
PDF: 09005aef826aa906
1Gb_DDR3_SDRAM.pdf - Rev. L 03/13 EN
Micron Technology, Inc. reserves the right to change products or specifications without notice.
139
2006 Micron Technology, Inc. All rights reserved.
MICRON [ MICRON TECHNOLOGY ]
