欢迎访问ic37.com |
会员登录 免费注册
发布采购

LAN9210 参数 Datasheet PDF下载

LAN9210图片预览
型号: LAN9210
PDF下载: 下载PDF文件 查看货源
内容描述: 外形小巧单芯片以太网控制器与HP Auto-MDIX的 [Small Form Factor Single- Chip Ethernet Controller with HP Auto-MDIX]
分类和应用: 控制器以太网
文件页数/大小: 458 页 / 4618 K
品牌: SMSC [ SMSC CORPORATION ]
 浏览型号LAN9210的Datasheet PDF文件第37页浏览型号LAN9210的Datasheet PDF文件第38页浏览型号LAN9210的Datasheet PDF文件第39页浏览型号LAN9210的Datasheet PDF文件第40页浏览型号LAN9210的Datasheet PDF文件第42页浏览型号LAN9210的Datasheet PDF文件第43页浏览型号LAN9210的Datasheet PDF文件第44页浏览型号LAN9210的Datasheet PDF文件第45页  
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface  
Datasheet  
Table 4.2 Soft-Strap Configuration Strap Definitions  
PIN / DEFAULT  
VALUE  
STRAP NAME  
DESCRIPTION  
LED_en_strap[7:0]  
LED Enable Straps: Configures the default value for the  
LED_EN bits in the LED Configuration Register  
(LED_CFG). A high value configures the associated  
LED/GPIO pin as a LED. A low value configures the  
associated LED/GPIO pin as a GPIO.  
LED_EN  
Note:  
One pin configures the default for all 8  
LED/GPIOs, but 8 separate bits are loaded by the  
EEPROM Loader, allowing individual control over  
each LED/GPIO.  
LED_fun_strap[1:0]  
auto_mdix_strap_1  
LED Function Straps: Configures the default value for the  
LED_FUN bits in the LED Configuration Register  
(LED_CFG). When configured low, the corresponding bit  
will be cleared. When configured high, the corresponding  
bit will be set.  
00b  
Port 1 Auto-MDIX Enable Strap: Configures the default  
value for the Auto-MDIX functionality on Port 1 when the  
AMDIXCTL bit in the Port x PHY Special Control/Status  
Indication Register  
AUTO_MDIX_1  
(PHY_SPECIAL_CONTROL_STAT_IND_x) is cleared.  
When configured low, Auto-MDIX is disabled. When  
configured high, Auto-MDIX is enabled.  
Note:  
If AMDIXCTL is set, this strap had no effect.  
manual_mdix_strap_1  
autoneg_strap_1  
Port 1 Manual MDIX Strap: Configures MDI(0) or MDIX(1)  
for Port 1 when the auto_mdix_strap_1 is low and the  
AMDIXCTL bit of the Port x PHY Special Control/Status  
Indication Register  
0b  
1b  
(PHY_SPECIAL_CONTROL_STAT_IND_x) is cleared.  
Port 1 Auto Negotiation Enable Strap: Configures the  
default value for the Auto-Negotiation (PHY_AN) enable bit  
in the PHY_BASIC_CTRL_1 register (See  
Section 14.4.2.1). When configured low, auto-negotiation is  
disabled. When configured high, auto-negotiation is  
enabled.  
This strap also affects the default value of the following bits:  
„ PHY_SPEED_SEL_LSB and PHY_DUPLEX bits of the  
Port x PHY Basic Control Register  
(PHY_BASIC_CONTROL_x)  
„ 10BASE-T Full Duplex (bit 6) and 10BASE-T Half Duplex  
(bit 5) bits of the Port x PHY Auto-Negotiation  
Advertisement Register (PHY_AN_ADV_x)  
„ MODE[2:0] bits of the Port x PHY Special Modes Register  
(PHY_SPECIAL_MODES_x)  
Refer to the respective register definition sections for  
additional information.  
SMSC LAN9312  
Revision 1.2 (04-08-08)  
DATA4S1HEET  
 复制成功!