欢迎访问ic37.com |
会员登录 免费注册
发布采购

LAN9210 参数 Datasheet PDF下载

LAN9210图片预览
型号: LAN9210
PDF下载: 下载PDF文件 查看货源
内容描述: 外形小巧单芯片以太网控制器与HP Auto-MDIX的 [Small Form Factor Single- Chip Ethernet Controller with HP Auto-MDIX]
分类和应用: 控制器以太网
文件页数/大小: 458 页 / 4618 K
品牌: SMSC [ SMSC CORPORATION ]
 浏览型号LAN9210的Datasheet PDF文件第39页浏览型号LAN9210的Datasheet PDF文件第40页浏览型号LAN9210的Datasheet PDF文件第41页浏览型号LAN9210的Datasheet PDF文件第42页浏览型号LAN9210的Datasheet PDF文件第44页浏览型号LAN9210的Datasheet PDF文件第45页浏览型号LAN9210的Datasheet PDF文件第46页浏览型号LAN9210的Datasheet PDF文件第47页  
High Performance Two Port 10/100 Managed Ethernet Switch with 32-Bit Non-PCI CPU Interface  
Datasheet  
Table 4.2 Soft-Strap Configuration Strap Definitions (continued)  
DESCRIPTION  
PIN / DEFAULT  
VALUE  
STRAP NAME  
manual_FC_strap_1  
Port 1 Manual Flow Control Enable Strap: Configures the  
default value of the Port 1 Full-Duplex Manual Flow Control  
Select (MANUAL_FC_1) bit in the Port 1 Manual Flow  
Control Register (MANUAL_FC_1). When configured low,  
flow control is determined by auto-negotiation (if enabled),  
and symmetric PAUSE is advertised (bit 10 of the Port x  
PHY Auto-Negotiation Advertisement Register  
0b  
(PHY_AN_ADV_x) is set).  
When configured high, flow control is determined by the  
Port 1 Full-Duplex Transmit Flow Control Enable  
(TX_FC_1) and Port 1 Full-Duplex Receive Flow Control  
Enable (RX_FC_1) bits, and symmetric PAUSE is not  
advertised (bit 10 of the Port x PHY Auto-Negotiation  
Advertisement Register (PHY_AN_ADV_x) is cleared).  
auto_mdix_strap_2  
Port 2 Auto-MDIX Enable Strap: Configures the default  
value for the Auto-MDIX functionality on Port 2 when the  
AMDIXCTL bit in the Port x PHY Special Control/Status  
Indication Register  
AUTO_MDIX_2  
(PHY_SPECIAL_CONTROL_STAT_IND_x) is cleared.  
When configured low, Auto-MDIX is disabled. When  
configured high, Auto-MDIX is enabled.  
Note:  
If AMDIXCTL is set, this strap had no effect.  
manual_mdix_strap_2  
autoneg_strap_2  
Port 2 Manual MDIX Strap: Configures MDI(0) or MDIX(1)  
for Port 2 when the auto_mdix_strap_2 is low and the  
AMDIXCTL bit of the Port x PHY Special Control/Status  
Indication Register  
0b  
1b  
(PHY_SPECIAL_CONTROL_STAT_IND_x) is cleared.  
Port 2 Auto Negotiation Enable Strap: Configures the  
default value for the Auto-Negotiation (PHY_AN) enable bit  
in the PHY_BASIC_CTRL_2 register (See  
Section 14.4.2.1). When configured low, auto-negotiation is  
disabled. When configured high, auto-negotiation is  
enabled.  
This strap also affects the default value of the following bits:  
„ PHY_SPEED_SEL_LSB and PHY_DUPLEX bits of the  
Port x PHY Basic Control Register  
(PHY_BASIC_CONTROL_x)  
„ 10BASE-T Full Duplex (bit 6) and 10BASE-T Half Duplex  
(bit 5) bits of the Port x PHY Auto-Negotiation  
Advertisement Register (PHY_AN_ADV_x)  
„ MODE[2:0] bits of the Port x PHY Special Modes Register  
(PHY_SPECIAL_MODES_x)  
Refer to the respective register definition sections for  
additional information.  
SMSC LAN9312  
Revision 1.2 (04-08-08)  
DATA4S3HEET  
 复制成功!