欢迎访问ic37.com |
会员登录 免费注册
发布采购

RTL8201BL 参数 Datasheet PDF下载

RTL8201BL图片预览
型号: RTL8201BL
PDF下载: 下载PDF文件 查看货源
内容描述: REALTEK单片单端口10 / 100M快速以太网PHYCEIVER RTL8201BL [REALTEK SINGLE CHIP SINGLE PORT 10/100M FAST ETHERNET PHYCEIVER RTL8201BL]
分类和应用: LTE以太网局域网(LAN)标准以太网:16GBASE-T
文件页数/大小: 29 页 / 335 K
品牌: ETC [ ETC ]
 浏览型号RTL8201BL的Datasheet PDF文件第5页浏览型号RTL8201BL的Datasheet PDF文件第6页浏览型号RTL8201BL的Datasheet PDF文件第7页浏览型号RTL8201BL的Datasheet PDF文件第8页浏览型号RTL8201BL的Datasheet PDF文件第10页浏览型号RTL8201BL的Datasheet PDF文件第11页浏览型号RTL8201BL的Datasheet PDF文件第12页浏览型号RTL8201BL的Datasheet PDF文件第13页  
RTL8201BL  
6.2 Register 1 Basic Mode Status Register  
Address  
1:<15>  
Name  
100Base-T4  
Description/Usage  
1 = enable 100Base-T4 support  
0 = suppress 100Base-T4 support  
Default/Attribute  
0, RO  
1, RO  
1, RO  
1, RO  
1, RO  
1:<14>  
1:<13>  
1:<12>  
1:<11>  
100Base_TX_ 1 = enable 100Base-TX full duplex support  
FD 0 = suppress 100Base-TX full duplex support  
100BASE_TX_ 1 = enable 100Base-TX half duplex support  
HD  
0 = suppress 100Base-TX half duplex support  
10Base_T_FD 1 = enable 10Base-T full duplex support  
0 = suppress 10Base-T full duplex support  
10_Base_T_HD 1 = enable 10Base-T half duplex support  
0 = suppress 10Base-T half duplex support  
Reserved  
1:<10:7>  
1:<6>  
MF Preamble The RTL8201BL will accept management frames  
1, RO  
Suppression  
with preamble suppressed. The RTL8201BL accepts  
management frames without preamble. A Minimum  
of 32 preamble bits are required for the first SMI  
read/write transaction after reset. One idle bit is  
required between any two management transactions  
as per IEEE802.3u specifications  
1:<5>  
1:<4>  
Auto  
1 = auto-negotiation process completed  
0, RO  
0, RO  
Negotiation  
Complete  
0 = auto-negotiation process not completed  
Remote Fault 1 = remote fault condition detected (cleared on read)  
0 = no remote fault condition detected  
When in 100Base-FX mode, this bit means an  
in-band signal Far-End-Fault is detected. Refer to  
Section 7.11.  
1:<3>  
1:<2>  
1:<1>  
1:<0>  
Auto  
1 = Link had not been experienced fail state  
0 = Link had been experienced fail state  
1 = valid link established  
1, RO  
0, RO  
0, RO  
1, RO  
Negotiation  
Link Status  
0 = no valid link established  
Jabber Detect 1 = jabber condition detected  
0 = no jabber condition detected  
Extended  
Capability  
1 = extended register capability  
0 = basic register capability only  
6.3. Register 2 PHY Identifier Register 1  
Address  
2:<15;0>  
Name  
PHYID1  
Description/Usage  
PHY identifier ID for software recognize  
RTL8201BL  
Default/Attribute  
0000, RO  
6.4. Register 3 PHY Identifier Register 2  
Address  
Name  
Description/Usage  
Default/Attribute  
3:<15;0>  
PHYID2  
PHY identifier ID for software recognize RTL8201  
8201, RO  
2002-03-29  
Rev.1.2  
9
 复制成功!