欢迎访问ic37.com |
会员登录 免费注册
发布采购

RTL8201BL 参数 Datasheet PDF下载

RTL8201BL图片预览
型号: RTL8201BL
PDF下载: 下载PDF文件 查看货源
内容描述: REALTEK单片单端口10 / 100M快速以太网PHYCEIVER RTL8201BL [REALTEK SINGLE CHIP SINGLE PORT 10/100M FAST ETHERNET PHYCEIVER RTL8201BL]
分类和应用: LTE以太网局域网(LAN)标准以太网:16GBASE-T
文件页数/大小: 29 页 / 335 K
品牌: ETC [ ETC ]
 浏览型号RTL8201BL的Datasheet PDF文件第2页浏览型号RTL8201BL的Datasheet PDF文件第3页浏览型号RTL8201BL的Datasheet PDF文件第4页浏览型号RTL8201BL的Datasheet PDF文件第5页浏览型号RTL8201BL的Datasheet PDF文件第7页浏览型号RTL8201BL的Datasheet PDF文件第8页浏览型号RTL8201BL的Datasheet PDF文件第9页浏览型号RTL8201BL的Datasheet PDF文件第10页  
RTL8201BL  
5.3 Clock Interface  
Symbol  
Type  
Pin No.  
Description  
X2  
O
47  
25MHz Crystal Output: This pin provides the 25MHz crystal output. It  
must be left open when X1 is driven with an external 25MHz oscillator.  
25MHz Crystal Input: This pin provides the 25MHz crystal input. If a  
25MHz oscillator is used, connect X1 to the oscillator’s output. Refer to  
section 8.3 to obtain clock source specifications.  
X1  
I
46  
5.4 100Mbps Network Interface  
Symbol  
Type  
Pin No.  
Description  
TPTX+  
O
34  
Transmit Output: Differential pair shared by 100Base-TX, 100Base-FX and  
10Base-T modes. When configured as 100Base-TX, output is an MLT-3  
encoded waveform. When configured as 100Base-FX, the output is  
pseudo-ECL level.  
TPTX-  
RTSET  
O
33  
I
28  
Transmit Bias Resistor Connection: This pin should be pulled to GND by  
a 5.9K(1%) resistor to define driving current for transmit DAC. The  
resistance value may be changed, depending on experimental results of the  
RTL8201BL.  
TPRX+  
TPRX-  
I
I
31  
30  
Receive Input: Differential pair shared by 100Base-TX, 100Base-FX, and  
10Base-T modes.  
5.5 Device Configuration Interface  
Symbol  
Type  
Pin No.  
Description  
ISOLATE  
I
43  
Set high to isolate the RTL8201BL from the MAC. This will also isolate the  
MDC/MDIO management interface. In this mode, the power consumption is  
minimum. This pin can be directly connected to GND or VCC.  
RPTR  
I
40  
39  
Set high to put the RTL8201BL into repeater mode. This pin can be directly  
connected to GND or VCC.  
SPEED  
LI  
This pin is latched to input during a power on or reset condition. Set high to  
put the RTL8201BL into 100Mbps operation. This pin can be directly connected  
to GND or VCC.  
This pin is latched to input during a power on or reset condition. Set high to  
enable full duplex. This pin can be directly connected to GND or VCC.  
This pin is latched to input during a power on or reset condition. Set high to  
enable Auto-negotiation mode, set low to force mode. This pin can be directly  
connected to GND or VCC.  
Set high to put the RTL8201BL into LDPS mode. This pin can be directly  
connected to GND or VCC. Refer to Section 7.7 for more information.  
This pin is latched to input during a power on or reset condition. Pull high to  
set the RTL8201BL into MII mode operation. Set low for SNI mode. This pin  
can be directly connected to GND or VCC. In test mode, this pin is an output pin and  
redefined as RTT3  
DUPLEX  
ANE  
LI  
LI  
38  
37  
LDPS  
I
41  
44  
MII/SNIB/  
RTT3(test)  
LI/O  
2002-03-29  
Rev.1.2  
6