欢迎访问ic37.com |
会员登录 免费注册
发布采购

AM29BDS320GTC9VMI 参数 Datasheet PDF下载

AM29BDS320GTC9VMI图片预览
型号: AM29BDS320GTC9VMI
PDF下载: 下载PDF文件 查看货源
内容描述: 32兆位(2M ×16位) , 1.8伏只同时读/写,突发模式闪存 [32 Megabit (2 M x 16-Bit), 1.8 Volt-only Simultaneous Read/Write, Burst Mode Flash Memory]
分类和应用: 闪存
文件页数/大小: 74 页 / 1108 K
品牌: SPANSION [ SPANSION ]
 浏览型号AM29BDS320GTC9VMI的Datasheet PDF文件第32页浏览型号AM29BDS320GTC9VMI的Datasheet PDF文件第33页浏览型号AM29BDS320GTC9VMI的Datasheet PDF文件第34页浏览型号AM29BDS320GTC9VMI的Datasheet PDF文件第35页浏览型号AM29BDS320GTC9VMI的Datasheet PDF文件第37页浏览型号AM29BDS320GTC9VMI的Datasheet PDF文件第38页浏览型号AM29BDS320GTC9VMI的Datasheet PDF文件第39页浏览型号AM29BDS320GTC9VMI的Datasheet PDF文件第40页  
P r e l i m i n a r y  
DQ7 or DQ6/DQ2 in the erasing bank. Refer to the “Write Operation Status” sec-  
tion on page 37 section for information on these status bits.  
Once the sector erase operation has begun, only the Erase Suspend command is  
valid. All other commands are ignored. However, note that a hardware reset im-  
mediately terminates the erase operation. If that occurs, the sector erase  
command sequence should be reinitiated once that bank has returned to reading  
array data, to ensure data integrity.  
The host system may also initiate the sector erase command sequence while the  
device is in the unlock bypass mode. The command sequence is four cycles cycles  
in length instead of six cycles.  
Figure 2 illustrates the algorithm for the erase operation. Refer to the Erase/Pro-  
gram Operations table in the AC Characteristics section for parameters and timing  
diagrams.  
Erase Suspend/Erase Resume Commands  
The Erase Suspend command, B0h, allows the system to interrupt a sector erase  
operation and then read data from, or program data to, any sector not selected  
for erasure. The bank address is required when writing this command. This com-  
mand is valid only during the sector erase operation, including the minimum 50  
µs time-out period during the sector erase command sequence. The Erase Sus-  
pend command is ignored if written during the chip erase operation or Embedded  
Program algorithm.  
When the Erase Suspend command is written during the sector erase operation,  
the device requires a maximum of 35 µs to suspend the erase operation. How-  
ever, when the Erase Suspend command is written during the sector erase time-  
out, the device immediately terminates the time-out period and suspends the  
erase operation.  
After the erase operation has been suspended, the bank enters the erase-sus-  
pend-read mode. The system can read data from or program data to any sector  
not selected for erasure. (The device “erase suspends” all sectors selected for  
erasure.) Reading at any address within erase-suspended sectors produces sta-  
tus information on DQ7–DQ0. The system can use DQ7, or DQ6 and DQ2  
together, to determine if a sector is actively erasing or is erase-suspended. Refer  
to the Write Operation Status section for information on these status bits.  
After an erase-suspended program operation is complete, the bank returns to the  
erase-suspend-read mode. The system can determine the status of the program  
operation using the DQ7 or DQ6 status bits, just as in the standard program op-  
eration. Refer to the “Write Operation Status” section for more information.  
In the erase-suspend-read mode, the system can also issue the autoselect com-  
mand sequence. Refer to the “Autoselect Functions” section on page 16 and  
“Autoselect Command Sequence” section on page 30 sections for details.  
To resume the sector erase operation, the system must write the Erase Resume  
command. The bank address of the erase-suspended bank is required when writ-  
ing this command. Further writes of the Resume command are ignored. Another  
Erase Suspend command can be written after the chip has resumed erasing.  
34  
Am29BDS320G  
27243B1 October 1, 2003