欢迎访问ic37.com |
会员登录 免费注册
发布采购

AM29BDS320GTC9VMI 参数 Datasheet PDF下载

AM29BDS320GTC9VMI图片预览
型号: AM29BDS320GTC9VMI
PDF下载: 下载PDF文件 查看货源
内容描述: 32兆位(2M ×16位) , 1.8伏只同时读/写,突发模式闪存 [32 Megabit (2 M x 16-Bit), 1.8 Volt-only Simultaneous Read/Write, Burst Mode Flash Memory]
分类和应用: 闪存
文件页数/大小: 74 页 / 1108 K
品牌: SPANSION [ SPANSION ]
 浏览型号AM29BDS320GTC9VMI的Datasheet PDF文件第28页浏览型号AM29BDS320GTC9VMI的Datasheet PDF文件第29页浏览型号AM29BDS320GTC9VMI的Datasheet PDF文件第30页浏览型号AM29BDS320GTC9VMI的Datasheet PDF文件第31页浏览型号AM29BDS320GTC9VMI的Datasheet PDF文件第33页浏览型号AM29BDS320GTC9VMI的Datasheet PDF文件第34页浏览型号AM29BDS320GTC9VMI的Datasheet PDF文件第35页浏览型号AM29BDS320GTC9VMI的Datasheet PDF文件第36页  
P r e l i m i n a r y  
Reset Command  
Writing the reset command resets the banks to the read or erase-suspend-read  
mode. Address bits are don’t cares for this command.  
The reset command may be written between the sequence cycles in an erase  
command sequence before erasing begins. This resets the bank to which the sys-  
tem was writing to the read mode. Once erasure begins, however, the device  
ignores reset commands until the operation is complete.  
The reset command may be written between the sequence cycles in a program  
command sequence before programming begins (prior to the third cycle). This re-  
sets the bank to which the system was writing to the read mode. If the program  
command sequence is written to a bank that is in the Erase Suspend mode, writ-  
ing the reset command returns that bank to the erase-suspend-read mode. Once  
programming begins, however, the device ignores reset commands until the op-  
eration is complete.  
The reset command may be written between the sequence cycles in an autoselect  
command sequence. Once in the autoselect mode, the reset command must be  
written to return to the read mode. If a bank entered the autoselect mode while  
in the Erase Suspend mode, writing the reset command returns that bank to the  
erase-suspend-read mode.  
If DQ5 goes high during a program or erase operation, writing the reset command  
returns the banks to the read mode (or erase-suspend-read mode if that bank  
was in Erase Suspend).  
The reset command is used to exit the sector lock/unlock sequence. This com-  
mand is required before reading from the bank selected for sector lock/unlock  
operations.  
Autoselect Command Sequence  
The autoselect command sequence allows the host system to access the manu-  
facturer and device codes, and determine whether or not a sector is protected.  
Table 14, “Command Definitions,on page 36 shows the address and data re-  
quirements. The autoselect command sequence may be written to an address  
within a bank that is either in the read or erase-suspend-read mode. The autose-  
lect command may not be written while the device is actively programming or  
erasing in the other bank.  
The autoselect command sequence is initiated by first writing two unlock cycles.  
This is followed by a third write cycle that contains the bank address and the au-  
toselect command. The bank then enters the autoselect mode. No subsequent  
data will be made available if the autoselect data is read in synchronous mode.  
The system may read at any address within the same bank any number of times  
without initiating another autoselect command sequence. The following table de-  
scribes the address requirements for the various autoselect functions, and the  
resulting data. BA represents the bank address, and SA represents the sector ad-  
dress. The device ID is read in three cycles.  
30  
Am29BDS320G  
27243B1 October 1, 2003