欢迎访问ic37.com |
会员登录 免费注册
发布采购

ACE9030MIWFP2Q 参数 Datasheet PDF下载

ACE9030MIWFP2Q图片预览
型号: ACE9030MIWFP2Q
PDF下载: 下载PDF文件 查看货源
内容描述: 无线接口和双合成器 [Radio Interface and Twin Synthesiser]
分类和应用: 无线
文件页数/大小: 39 页 / 382 K
品牌: MITEL [ MITEL NETWORKS CORPORATION ]
 浏览型号ACE9030MIWFP2Q的Datasheet PDF文件第4页浏览型号ACE9030MIWFP2Q的Datasheet PDF文件第5页浏览型号ACE9030MIWFP2Q的Datasheet PDF文件第6页浏览型号ACE9030MIWFP2Q的Datasheet PDF文件第7页浏览型号ACE9030MIWFP2Q的Datasheet PDF文件第9页浏览型号ACE9030MIWFP2Q的Datasheet PDF文件第10页浏览型号ACE9030MIWFP2Q的Datasheet PDF文件第11页浏览型号ACE9030MIWFP2Q的Datasheet PDF文件第12页  
ACE9030  
ELECTRICAL CHARACTERISTICS  
These characteristics apply over these ranges of conditions (unless otherwise stated):  
TAMB = – 40 °C to + 85 °C, all VDD = + 3·6 to + 5·0 V, GND ref. = VSS  
A.C. Characteristics (continued)  
Parameter  
Min.  
Typ.  
Max.  
Unit Conditions  
LOW FREQUENCY AMPLIFIERS (1 and 2)  
Voltage Gain  
Input Offset  
Open loop input resistance  
Open loop output resistance  
Unity Gain bandwidth  
1200  
2800  
10  
1
8
2
20  
mV  
MΩ  
kΩ  
MHz  
nA  
dB  
V
V
V
V
V
Input bias current, inverting input  
Power supply rejection at 120 Hz, 10 kHz  
Output voltage maximum  
Output voltage maximum, as a comparator  
Output voltage minimum level  
Output voltage minimum level  
Common mode input range (LF1 1)  
Common mode input range (LF1 2)  
Output slew rate  
200  
40  
VDDA – 0·2  
VDDA – 0·1  
50  
10 kto 6ND  
10 kto 6ND  
10 kto 6ND  
10 kto 6ND  
0·2  
0·1  
2.5  
VSSA  
VSSA  
0.15  
VDDA  
0.25  
V/µs  
Output load capacitance  
30  
pF  
8 MHz OSCILLATOR and PLL  
OSC8 centre frequency  
OSC8 VCO sensitivity  
OSC8 charge pump output current  
CLK8 output load, resistive:  
capacitive:  
8·064  
25  
50  
25  
25  
MHz  
MHz/V  
µA  
kΩ  
pF  
15  
15  
100  
30  
CLK8 output amplitude  
CLK8 total output jitter  
Start-up time at power-on, to default settings  
0·8  
1·0  
2·4  
500  
15  
Vpk-pk  
Hz 0 - 3 kHz  
ms With a loop filter as  
described in fig. 17  
Lock time to within 125 ppm, after  
reprogramming set-ups  
15  
ms  
AFCIN F.M. DISCRIMINATOR and AFC  
AFCIN input signal level  
AFCIN input impedance, resistive:  
capacitive:  
0·05  
50  
2·5  
Vpk-pk  
kΩ  
pF  
10  
Input frequency  
Input signal to integrated noise ratio  
Input Schmitt Hysteresis  
400  
10  
8
500  
kHz  
dB I.F. ± 15 kHz.  
mV  
AUDIO signal SINAD, psophometric, note 7  
AUDIO signal hum and noise, note 7  
AUDIO output signal level, note 7  
AFCOUT load  
AFCOUT duty cycle  
AFCOUT rise and fall times  
40  
45  
dB 1 kHz tone at 3 kHz  
dB peak deviation on  
mVrms AFCIN input at I.F.  
pF  
%
– 46  
195  
37  
260  
30  
63  
75  
ns  
Note  
7. AUDIO signal quality is measured with feedback components as shown in figure 18 and with 500 mV peak to peak input to AFCIN.  
Discriminator gain is set with D = 3 and M = 40 and VDD = 3·75 V and a crystal at 14·85 MHz. SINAD is defined as the ratio of wanted signal  
to all unwanted output, measured simultaneously with filters. The hum and noise figure is defined as the ratio of output power at AUDIO when  
AFCIN is unmodulated to the output power when AFCIN is driven as specified above.  
8