Numonyx® Embedded Flash Memory (J3 65 nm) Single Bit per Cell (SBC)
6.0
Electrical Characteristics
6.1
DC Current Specifications
Table 7:
DC Current Characteristics
VCCQ
VCC
Parameter
2.7 - 3.6V
2.7 - 3.6V
Test Conditions
Notes
Symbol
Typ
Max Unit
V
CC = VCC Max; VCCQ = VCCQ Max
ILI
Input and VPEN Load Current
Output Leakage Current
—
1
μA
μA
1
1
VIN = VCCQ or VSS
VCC= VCC Max; VCCQ = VCCQ Max
VIN = VCCQ or VSS
ILO
—
10
CMOS Inputs, VCC = VCC Max; Vccq =
VccqMax
Device is disabled (see Table 17, “Chip
Enable Truth Table for 32-, 64-,
128-Mb” on page 30),
RP# = VCCQ ± 0.2 V
50
120
μA
ICCS
VCC Standby Current
1,2,3
TTL Inputs, VCC = VCC Max,
Vccq = VccqMax
0.71
50
2
mA
Device is disabled (see Table 17, “Chip
Enable Truth Table for 32-, 64-,
128-Mb” on page 30), RP# = VIH
ICCD
VCC Power-Down Current
120
μA
RP# = VSS ± 0.2 V, IOUT (STS) = 0 mA
—
CMOS Inputs, VCC = VCC Max, VCCQ = VCCQ
Max using standard 8 word page mode
reads.
15
30
20
54
mA
mA
Device is enabled (see Table 17, “Chip
Enable Truth Table for 32-, 64-,
128-Mb” on page 30)
f = 5 MHz, IOUT = 0 mA
ICCR
8-Word Page
1,3
CMOS Inputs,VCC = VCC Max, VCCQ = VCCQ
Max using standard 8 word page mode
reads.
Device is enabled (see Table 17, “Chip
Enable Truth Table for 32-, 64-,
128-Mb” on page 30)
f = 33 MHz, IOUT = 0 mA
35
40
35
40
60
70
70
80
mA
mA
mA
mA
CMOS Inputs, VPEN = VCC
TTL Inputs, VPEN = VCC
ICCW
VCC Program or Set Lock-Bit Current
1,4
1,4
1,5
CMOS Inputs, VPEN = VCC
TTL Inputs, VPEN = VCC
ICCE
ICCBC
VCC Block Erase or VCC Blank Check or
Clear Block Lock-Bits Current
Device is enabled (see Table 17, “Chip
ICCWS
ICCES
VCC Program Suspend or Block Erase
Suspend Current
—
10
mA Enable Truth Table for 32-, 64-,
128-Mb” on page 30)
Notes:
1.
All currents are in RMS unless otherwise noted. These currents are valid for all product versions (packages and speeds).
Contact Numonyx or your local sales office for information about typical specifications.
Includes STS.
CMOS inputs are either VCC ± 0.2 V or VSS ± 0.2 V. TTL inputs are either VIL or VIH
Sampled, not 100% tested.
2.
3.
4.
5.
.
ICCWS and ICCES are specified with the device selected. If the device is read or written while in erase suspend mode, the
device’s current draw is ICCR and ICCWS
.
Jan 2011
208032-03
Datasheet
21