TMS320F2809, TMS320F2808, TMS320F2806
TMS320F2802, TMS320F2801, UCD9501
TMS320C2802, TMS320C2801, and TMS320F2801x DSPs
www.ti.com
SPRS230H–OCTOBER 2003–REVISED JUNE 2006
6.9.7 On-Chip Analog-to-Digital Converter
Table 6-38. ADC Electrical Characteristics (over recommended operating conditions)(1)(2)
PARAMETER
DC SPECIFICATIONS
Resolution
MIN
TYP
MAX
UNIT
12
0.001
0.001
Bits
MHz
MHz
ADC clock
60-MHz device
100-MHz device
7.5
12.5
ACCURACY
INL (Integral nonlinearity)
DNL (Differential nonlinearity)(3)
1-12.5 MHz ADC clock (6.25 MSPS)
1-12.5 MHz ADC clock (6.25 MSPS)
±1.5
±1
LSB
LSB
LSB
LSB
LSB
LSB
LSB
LSB
(4)
Offset error
-60
+60
Offset error with hardware trimming
Overall gain error with internal reference
Overall gain error with external reference
Channel-to-channel offset variation
Channel-to-channel gain variation
ANALOG INPUT
±4
(5)
-60
-60
+60
+60
±4
±4
(6)
Analog input voltage (ADCINx to ADCLO)
ADCLO
0
3
5
V
-5
0
mV
pF
µA
Input capacitance
10
Input leakage current
±5
(5)
INTERNAL VOLTAGE REFERENCE
VADCREFP - ADCREFP output voltage at the pin based on
internal reference
1.275
0.525
V
V
VADCREFM - ADCREFM output voltage at the pin based on
internal reference
Voltage difference, ADCREFP - ADCREFM
Temperature coefficient
0.75
50
V
PPM/°C
EXTERNAL VOLTAGE REFERENCE(5)(7)
ADCREFSEL[15:14] = 11b
ADCREFSEL[15:14] = 10b
ADCREFSEL[15:14] = 01b
1.024
1.500
2.048
V
V
V
VADCREFIN - External reference voltage input on ADCREFIN
pin 0.2% or better accurate reference recommended
AC SPECIFICATIONS
SINAD (100 kHz) Signal-to-noise ratio + distortion
SNR (100 kHz) Signal-to-noise ratio
THD (100 kHz) Total harmonic distortion
ENOB (100 kHz) Effective number of bits
SFDR (100 kHz) Spurious free dynamic range
67.5
68
dB
dB
-79
10.9
83
dB
Bits
dB
(1) Tested at 12.5 MHz ADCCLK.
(2) All voltages listed in this table are with respect to VSSA2
(3) TI specifies that the ADC will have no missing codes.
(4) 1 LSB has the weighted value of 3.0/4096 = 0.732 mV.
.
(5) A single internal/external band gap reference sources both ADCREFP and ADCREFM signals, and hence, these voltages track
together. The ADC converter uses the difference between these two as its reference. The total gain error listed for the internal reference
is inclusive of the movement of the internal bandgap over temperature. Gain error over temperature for the external reference option will
depend on the temperature profile of the source used.
(6) Voltages above VDDA + 0.3 V or below VSS - 0.3 V applied to an analog input pin may temporarily affect the conversion of another pin.
To avoid this, the analog inputs should be kept within these limits.
(7) TI recommends using high precision external reference TI part REF3020/3120 or equivalent for 2.048-V reference.
118
Electrical Specifications
TI [ TEXAS INSTRUMENTS ]
