TMS320F2809, TMS320F2808, TMS320F2806
TMS320F2802, TMS320F2801, UCD9501
TMS320C2802, TMS320C2801, and TMS320F2801x DSPs
www.ti.com
SPRS230H–OCTOBER 2003–REVISED JUNE 2006
Table 6-35. SPI Master Mode External Timing (Clock Phase = 1)(1)(2)(3)(4)(5)
NO.
SPI WHEN (SPIBRR + 1) IS EVEN
OR SPIBRR = 0 OR 2
SPI WHEN (SPIBRR + 1) IS ODD
AND SPIBRR > 3
UNIT
MIN
4tc(LCO)
MAX
MIN
MAX
1
2
tc(SPC)M
Cycle time, SPICLK
128tc(LCO)
0.5tc(SPC)M
5tc(LCO)
127tc(LCO)
ns
ns
tw(SPCH)M
Pulse duration, SPICLK high (clock
polarity = 0)
0.5tc(SPC)M -10
0.5tc(SPC)M - 0.5tc (LCO)-10
0.5tc(SPC)M - 0.5tc (LCO)-10
0.5tc(SPC)M + 0.5tc(LCO) - 10
0.5tc(SPC)M + 0.5tc(LCO) -10
0.5tc(SPC)M - 10
0.5tc(SPC)M - 0.5tc(LCO)
0.5tc(SPC)M - 0.5tc(LCO
0.5tc(SPC)M + 0.5tc(LCO)
0.5tc(SPC)M + 0.5tc(LCO)
tw(SPCL))M
Pulse duration, SPICLK low (clock
polarity = 1)
0.5tc(SPC)M -10
0.5tc(SPC)M -10
0.5tc(SPC)M -10
0.5tc(SPC)M -10
0.5tc(SPC)M
0.5tc(SPC)M
0.5tc(SPC)M
ns
ns
ns
ns
3
6
tw(SPCL)M
Pulse duration, SPICLK low (clock
polarity = 0)
tw(SPCH)M
Pulse duration, SPICLK high (clock
polarity = 1)
tsu(SIMO-SPCH)M
Setup time, SPISIMO data valid
before SPICLK high (clock polarity
= 0)
tsu(SIMO-SPCL)M
Setup time, SPISIMO data valid
before SPICLK low (clock polarity =
1)
0.5tc(SPC)M -10
0.5tc(SPC)M - 10
ns
7
tv(SPCH-SIMO)M
tv(SPCL-SIMO)M
tsu(SOMI-SPCH)M
tsu(SOMI-SPCL)M
tv(SPCH-SOMI)M
tv(SPCL-SOMI)M
Valid time, SPISIMO data valid after
SPICLK high (clock polarity = 0)
0.5tc(SPC)M -10
0.5tc(SPC)M -10
35
0.5tc(SPC)M - 10
0.5tc(SPC)M -10
35
ns
ns
ns
ns
ns
ns
Valid time, SPISIMO data valid after
SPICLK low (clock polarity = 1)
10
11
Setup time, SPISOMI before
SPICLK high (clock polarity = 0)
Setup time, SPISOMI before
SPICLK low (clock polarity = 1)
35
35
Valid time, SPISOMI data valid after
SPICLK high (clock polarity = 0)
0.25tc(SPC)M -10
0.25tc(SPC)M -10
0.5tc(SPC)M -10
0.5tc(SPC)M -10
Valid time, SPISOMI data valid after
SPICLK low (clock polarity = 1)
(1) The MASTER/SLAVE bit (SPICTL.2) is set and the CLOCK PHASE bit (SPICTL.3) is set.
(2) tc(SPC) = SPI clock cycle time = LSPCLK/4 or LSPCLK/(SPIBRR + 1)
(3) Internal clock prescalers must be adjusted such that the SPI clock speed is limited to the following SPI clock rate:
Master mode transmit 25 MHz MAX, master mode receive 12.5 MHz MAX
Slave mode transmit 12.5 MHz MAX, slave mode receive 12.5 MHz MAX.
(4) tc(LCO) = LSPCLK cycle time
(5) The active edge of the SPICLK signal referenced is controlled by the CLOCK POLARITY bit (SPICCR.6).
114
Electrical Specifications
TI [ TEXAS INSTRUMENTS ]
