MITSUBISHI SEMICONDUCTOR <Dual-In-Line Package Intelligent Power Module>
PS21265-P/AP
TRANSFER-MOLD TYPE
INSULATED TYPE
THERMAL RESISTANCE
Limits
Symbol
Parameter
Condition
Unit
Min.
—
Typ.
—
Max.
1.95
Rth(j-c)Q
Rth(j-c)F
Rth(c-f)F
Inverter IGBT part (per 1/6 module)
°C/W
°C/W
°C/W
Junction to case thermal
resistance
(Note 3)
Inverter FWDi part (per 1/6 module)
—
—
3.00
Contact thermal resistance
—
—
0.067
Case to fin (per 1 module) thermal grease applied
Note 3 : Grease with good thermal conductivity should be applied evenly with a thickness of about +100µm~+200µm on the contact surface
of DIP-IPM and heat-sink.
ELECTRICAL CHARACTERISTICS (Tj = 25°C, unless otherwise noted)
INVERTER PART
Limits
Symbol
VCE(sat)
Parameter
Condition
Unit
V
Min.
—
Typ.
Max.
2.05
2.15
2.00
1.85
—
VD = VDB = 15V
VIN = 5V
IC = 20A, Tj = 25°C
IC = 20A, Tj = 125°C
Tj = 25°C, –IC = 20A, VIN = 0V
1.55
1.65
1.50
1.25
0.30
0.40
1.50
0.50
—
Collector-emitter saturation
voltage
—
—
FWDi forward voltage
VEC
ton
trr
V
µs
0.65
—
µs
µs
µs
µs
VCC = 300V, VD = VDB = 15V
—
↔
5V
tc(on)
toff
tc(off)
IC = 20A, Tj = 125°C, VIN = 0
0.60
2.10
0.80
1
Switching times
—
Inductive load (upper-lower arm)
—
Tj = 25°C
Tj = 125°C
—
Collector-emitter cut-off
current
ICES
mA
VCE = VCES
—
—
10
CONTROL (PROTECTION) PART
Symbol
Parameter
Limits
Typ.
—
Condition
Unit
Min.
—
—
Max.
7.00
0.55
7.00
0.55
—
mA
mA
mA
mA
V
VD = VDB = 15V
VIN = 5V
Total of VP1-VPC, VN1-VNC
VUFB-VUFS, VVFB-VVFS, VWFB-VWFS
Total of VP1-VPC, VN1-VNC
—
ID
Circuit current
—
—
VD = VDB = 15V
VIN = 0V
—
—
VUFB-VUFS, VVFB-VVFS, VWFB-VWFS
4.9
—
—
VFOH
VFOL
VSC(ref)
IIN
VSC = 0V, FO circuit pull-up to 5V with 10kΩ
VSC = 1V, IFO = 1mA
TC = –20~100°C, VD = 15V
VIN = 5V
Fault output voltage
—
—
0.95
0.52
2.0
V
V
Short circuit trip level
Input current
0.45
1.0
10.0
10.5
10.3
10.8
1.0
2.1
0.8
(Note 4)
1.5
—
mA
V
Trip level
12.0
12.5
12.5
13.0
—
UVDBt
UVDBr
UVDt
UVDr
tFO
Reset level
—
V
Control supply under-voltage
protection
Tj ≤ 125°C
Trip level
—
—
V
V
Reset level
CFO = 22nF
1.8
2.3
1.4
ms
V
(Note 5)
Fault output pulse width
ON threshold voltage
OFF threshold voltage
2.6
Vth(on)
Vth(off)
Applied between UP, VP, WP-VPC, UN, VN, WN-VNC
2.1
V
Note 4: Short circuit protection is functioning only at the low-arms. Please select the external shunt resistance such that the SC trip-level is
less than 2.0 times of the collector current rating (20A).
5: Fault signal is output when the low-arms short circuit or control supply under-voltage protective functions operate. The fault output pulse-
width tFO depends on the capacitance value of CFO according to the following approximate equation : CFO = 12.2 ✕ 10-6 ✕ tFO [F].
Oct. 2005
MITSUBISHI [ Mitsubishi Group ]
