PIC18F2331/2431/4331/4431
TABLE 5-3:
Register
INITIALIZATION CONDITIONS FOR ALL REGISTERS (CONTINUED)
MCLR Resets
WDT Reset
Power-on Reset,
Brown-out Reset
Wake-up via WDT
or Interrupt
Applicable Devices
RESETInstruction
Stack Resets
FSR1H
FSR1L
BSR
2331 2431 4331 4431
2331 2431 4331 4431
2331 2431 4331 4431
2331 2431 4331 4431
2331 2431 4331 4431
---- 0000
xxxx xxxx
---- 0000
N/A
---- uuuu
uuuu uuuu
---- 0000
N/A
---- uuuu
uuuu uuuu
---- uuuu
N/A
INDF2
POSTINC2
N/A
N/A
N/A
POSTDEC2 2331 2431 4331 4431
N/A
N/A
N/A
PREINC2
PLUSW2
FSR2H
2331 2431 4331 4431
2331 2431 4331 4431
2331 2431 4331 4431
2331 2431 4331 4431
2331 2431 4331 4431
2331 2431 4331 4431
2331 2431 4331 4431
2331 2431 4331 4431
2331 2431 4331 4431
2331 2431 4331 4431
2331 2431 4331 4431
2331 2431 4331 4431
2331 2431 4331 4431
2331 2431 4331 4431
2331 2431 4331 4431
2331 2431 4331 4431
2331 2431 4331 4431
2331 2431 4331 4431
2331 2431 4331 4431
2331 2431 4331 4431
2331 2431 4331 4431
2331 2431 4331 4431
N/A
N/A
N/A
N/A
N/A
N/A
---- 0000
xxxx xxxx
---x xxxx
0000 0000
xxxx xxxx
1111 1111
0000 q000
--00 0101
0--- ---0
0--1 11q0
xxxx xxxx
xxxx xxxx
0000 0000
0000 0000
1111 1111
-000 0000
xxxx xxxx
0000 0000
0000 0000
0000 0000
---- uuuu
uuuu uuuu
---u uuuu
0000 0000
uuuu uuuu
1111 1111
0000 q000
--00 0101
0--- ---0
0--q qquu
uuuu uuuu
uuuu uuuu
u0uu uuuu
0000 0000
1111 1111
-000 0000
uuuu uuuu
0000 0000
0000 0000
0000 0000
---- uuuu
uuuu uuuu
---u uuuu
uuuu uuuu
uuuu uuuu
uuuu uuuu
uuuu uuuu
--uu uuuu
u--- ---u
u--u qquu
uuuu uuuu
uuuu uuuu
uuuu uuuu
uuuu uuuu
1111 1111
-uuu uuuu
uuuu uuuu
uuuu uuuu
uuuu uuuu
uuuu uuuu
FSR2L
STATUS
TMR0H
TMR0L
T0CON
OSCCON
LVDCON
WDTCON
RCON(4)
TMR1H
TMR1L
T1CON
TMR2
PR2
T2CON
SSPBUF
SSPADD
SSPSTAT
SSPCON
Legend: u= unchanged, x= unknown, -= unimplemented bit, read as ‘0’, q= value depends on condition.
Shaded cells indicate conditions do not apply for the designated device.
Note 1: One or more bits in the INTCONx or PIRx registers will be affected (to cause wake-up).
2: When the wake-up is due to an interrupt and the GIEL or GIEH bit is set, the PC is loaded with the
interrupt vector (0008h or 0018h).
3: When the wake-up is due to an interrupt and the GIEL or GIEH bit is set, the TOSU, TOSH and TOSL are
updated with the current value of the PC. The STKPTR is modified to point to the next location in the
hardware stack.
4: See Table 5-2 for Reset value for specific condition.
5: Bits 6 and 7 of PORTA, LATA and TRISA are enabled depending on the oscillator mode selected. When
not enabled as PORTA pins, they are disabled and read ‘0’.
6: Bit 3 of PORTE and LATE are enabled if MCLR functionality is disabled. When not enabled as the PORTE
pin, they are disabled and read as ‘0’. The 28-pin devices do not have only RE3 implemented.
2010 Microchip Technology Inc.
DS39616D-page 55
MICROCHIP [ MICROCHIP ]
