欢迎访问ic37.com |
会员登录 免费注册
发布采购

XC836 参数 Datasheet PDF下载

XC836图片预览
型号: XC836
PDF下载: 下载PDF文件 查看货源
内容描述: 8位单芯片微控制器 [8-Bit Single-Chip Microcontroller]
分类和应用: 微控制器
文件页数/大小: 56 页 / 1355 K
品牌: INFINEON [ Infineon ]
 浏览型号XC836的Datasheet PDF文件第37页浏览型号XC836的Datasheet PDF文件第38页浏览型号XC836的Datasheet PDF文件第39页浏览型号XC836的Datasheet PDF文件第40页浏览型号XC836的Datasheet PDF文件第42页浏览型号XC836的Datasheet PDF文件第43页浏览型号XC836的Datasheet PDF文件第44页浏览型号XC836的Datasheet PDF文件第45页  
XC835/836  
Electrical Parameters  
Table 16 shows the maximum active current within the device in the reduced voltage  
condition of 2.5 V < VDDP < 3.0 V. The active current consumption needs to be below the  
specified values as according to the VDDP voltage. If the conditions are not met, a  
brownout reset may be triggered.  
Table 16  
VDDP  
Active Current Consumption in Reduced Voltage Condition  
2.5 V  
2.6 V  
2.7 V  
2.8 V  
Maximum active current 7 mA  
13 mA  
20 mA  
25 mA  
Table 17 provides the active current consumption of some modules operating at 8 MHz  
active mode, 3 V power supply at 25° C. The typical values shown are used as a  
reference guide for device operating in reduced voltage conditions.  
Table 17  
Typical Active Current Consumption1) 2)  
Active Current  
Symbol  
Limit Values Unit Test Condition  
Typ.  
Consumption  
Baseload current3) ICPUDDC  
6900  
µA  
Modules including Core,  
memories, UART, T0, T1 and  
EVR. Disable ADC analog  
(GLOBCTR.ANON = 0).  
ADC4)  
IADCDDC  
3760  
µA  
Set PMCON1.ADC_DIS to 0  
and GLOBECTR. ANON to 1  
SSC5)  
ISSCDDC  
ICCU6DDC  
IT2DDC  
IMDUDDC  
ICORDICDDC 1880  
460  
3320  
200  
µA  
µA  
µA  
µA  
µA  
µA  
µA  
Set PMCON1.SSC_DIS to 0  
Set PMCON1.CCU_DIS to 0  
Set PMCON1.T2_DIS to 0  
Set PMCON1.MDU_DIS to 0  
Set PMCON1.CDC_DIS to 0  
Set PMCON1.LTS_DIS to 0  
Set PMCON1.IIC_DIS to 0  
CCU66)  
Timer 27)  
MDU8)  
1260  
CORDIC9)  
LEDTSCU10)  
IIC11)  
ILEDDDC  
IIICDDC  
850  
580  
1) Modules that are controllable by programming the register PMCON1.  
2) Not subject to production test, verified by design/characterisation.  
3) Baseload current is measured when the device is running in user mode with an endless loop in the flash  
memory. All modules in register PMCON1 are disabled.  
4) ADC active current is measured with: module enable, ADC analog clock at 8MHz, running in parallel  
conversion request in autoscan mode for 4 channels  
5) SSC active curremt is measured with: module enabled, running in loop back mode at a baud rate of 1 MBaud  
6) CCU6 active current is measured with: module enabled, all timers running in 8 MHz, 6 PWM outputs are  
generated.  
Data Sheet  
36  
V1.2, 2011-03  
 复制成功!