欢迎访问ic37.com |
会员登录 免费注册
发布采购

FT2232C_04 参数 Datasheet PDF下载

FT2232C_04图片预览
型号: FT2232C_04
PDF下载: 下载PDF文件 查看货源
内容描述: 双USB UART / FIFO I.C. [Dual USB UART / FIFO I.C.]
分类和应用: 先进先出芯片
文件页数/大小: 54 页 / 1025 K
品牌: FTDI [ FUTURE TECHNOLOGY DEVICES INTERNATIONAL LTD. ]
 浏览型号FT2232C_04的Datasheet PDF文件第15页浏览型号FT2232C_04的Datasheet PDF文件第16页浏览型号FT2232C_04的Datasheet PDF文件第17页浏览型号FT2232C_04的Datasheet PDF文件第18页浏览型号FT2232C_04的Datasheet PDF文件第20页浏览型号FT2232C_04的Datasheet PDF文件第21页浏览型号FT2232C_04的Datasheet PDF文件第22页浏览型号FT2232C_04的Datasheet PDF文件第23页  
FT2232C Dual USB UART / FIFO I.C.  
8.0 Standard Device Configuration Examples  
8.1 Oscillator Configurations  
FT2232C  
FT2232C  
27pF  
43  
43  
XTIN  
XTIN  
3-Pin Resonator  
6MHz  
2 - Pin Resonator  
or Crystal  
1M  
6MHz  
27pF  
44  
44  
XTOUT  
XTOUT  
Figure 5  
Figure 6  
3-Pin Ceramic Resonator Configuration  
Crystal or 2-Pin Ceramic Resonator  
Configuration  
Figure 5 illustrates how to use the FT2232C with a 3-Pin Ceramic Resonator. A suitable part would be a ceramic  
resonator from Murata’s CERALOCK range. (Murata Part Number CSTCR6M00G15), or equivalent. 3-Pin ceramic  
resonators have the load capacitors built into the resonator so no external loading capacitors are required. This makes  
for an economical configuration. The accuracy of this Murata ceramic resonator is +/- 0.25% and it is specifically  
designed for USB full speed applications. A 1 MegaOhm loading resistor across XTIN and XTOUT is recommended in  
order to guarantee this level of accuracy.  
Other ceramic resonators with a lesser degree of accuracy (typically +/- 0.5%) are technically out-with the USB  
specification, but it has been calculated that using such a device will work satisfactorily in practice with a FT2232C  
design. An example of such a device is Murata’s CSTLSM00G53.  
Figure 6 illustrates how to use the FT2232C with a 6MHz Crystal or 2-Pin Ceramic Resonator. In this case, these  
devices do not have in-built loading capacitors so these have to be added between XTIN, XTOUT and GND as  
shown. A value of 27pF is shown as the capacitor in the example – this will be good for many crystals and some  
resonators but do select the value based on the manufacturers recommendations wherever possible. If using a crystal,  
use a parallel cut type. If using a resonator, see the previous note on frequency accuracy.  
It is also possible to use a 6 MHz Oscillator with the FT2232C. In this case the output of the oscillator would be  
connected to XTIN, and XTOUT should be left unconnected. The oscillator must have a CMOS output.  
DS2232C Version 1.2  
© Future Technology Devices International Ltd. 2004  
Page 19 of 54  
 复制成功!