ELECTRICAL CHARACTERISTICS
STATIC ELECTRICAL CHARACTERISTICS
STATIC ELECTRICAL CHARACTERISTICS
Table 3. Static Electrical Characteristics
Characteristics noted under conditions of 3.0V ≤ VDD ≤ 5.5V, 9.0V ≤ VPWR ≤ 18V, -40°C ≤ TC ≤ 125°C, and calibrated timers,
unless otherwise noted. Where typical values reflect the parameter’s approx. average value with VPWR = 13V, TA = 25°C.
Characteristic
Symbol
Min
Typ
Max
Unit
POWER INPUT (VDD, VPWR)
Supply Voltage(4)
Fully Operational
Full Parameter Specification
V
4.5
9.0
–
36
18
V
PWR(FO)
Supply Current
I
mA
(
)
VPWR ON
All Outputs Disabled (Normal Mode)
–
10.0
14.0
Sleep State Supply Current (Must have V
VPWR = 18V
≤ 0.8V for sleep state),
I
µA
DD
VPWR(SS)
–
15
39
1.5
4.0
200
–
30
42
V
V
V
V
V
Over-voltage Shutdown Threshold Voltage(5)
VPWR(OV)
36.5
0.5
3.0
100
5.3
3.0
V
V
PWR
PWR
PWR
PWR
PWR
Over-voltage Shutdown Hysteresis Voltage
V
3.0
4.4
300
8.99
5.5
PWR(OV-HYS)
VPWR(UV)
Under-voltage Shutdown Threshold Voltage(6)
Under-voltage Shutdown Hysteresis Voltage
Low Operating Voltage (Low-voltage reported via the SPI)(7)
V
VPWR(UV-HYS)
VPWR(LOV)
mV
V
VDD Supply Voltage
V
–
V
DD
VDD Supply Current
I
mA
VDD
Static Condition and does not include VDD current out of device
–
–
1.0
2.8
VDD Supply Under-voltage (Sleep State) Threshold Voltage(8)
INJECTOR DRIVER OUTPUTS (OUT 0:3)
Drain-to-Source ON Resistance
V
0.8
2.5
V
DD(UV)
R
Ω
DS(ON)
–
–
–
–
0.2
–
0.3
–
I
I
I
= 1.0A, T = 125°C, VPWR = 13V
OUT
OUT
OUT
J
= 1.0A, T = 25°C, VPWR = 13V
J
= 1.0A, T = -40°C, VPWR = 13V
–
J
Output Self Limiting Current
I
3.0
–
6.0
A
V
OUT(LIM)
Output Fault Detection Voltage Threshold(9)
Outputs Programmed OFF (Open Load)
Outputs Programmed ON (Short to Battery)
V
OUT(FLT-TH)
2.0
2.5
3.0
Output OFF Open Load Detection Current
I
µA
(OFF)OCO
V
= 18V, Outputs Programmed OFF
40
20
75
100
200
DRAIN
Output ON Open Load Detection Current
I
mA
(ON)OCO
Current less then specification value considered open
100
Notes
4. These parameters are guaranteed by design, but not production tested. Fully operational means driver outputs will toggle as expected
with input toggling. SPI is guaranteed to be operational when VPWR > 4.5V. SPI may not report correctly when VPWR < 4.5V.
5. Over-voltage thresholds minimum and maximum include hysteresis.
6. Under-voltage thresholds minimum and maximum include hysteresis.
7. Device is functional provided TJ is less than 150°C. Some table parameters may be out of specification.
8. Device in Sleep State, returns from sleep state with power on reset.
9. Output fault detection thresholds with outputs programmed OFF. Output fault detect thresholds are the same for output open and shorts.
33810
Analog Integrated Circuit Device Data
Freescale Semiconductor
6
FREESCALE [ Freescale ]
