欢迎访问ic37.com |
会员登录 免费注册
发布采购

FM24C02 参数 Datasheet PDF下载

FM24C02图片预览
型号: FM24C02
PDF下载: 下载PDF文件 查看货源
内容描述: 4K位标准2线总线接口的串行EEPROM [4K-Bit Standard 2-Wire Bus Interface Serial EEPROM]
分类和应用: 可编程只读存储器电动程控只读存储器电可擦编程只读存储器
文件页数/大小: 14 页 / 107 K
品牌: FAIRCHILD [ FAIRCHILD SEMICONDUCTOR ]
 浏览型号FM24C02的Datasheet PDF文件第6页浏览型号FM24C02的Datasheet PDF文件第7页浏览型号FM24C02的Datasheet PDF文件第8页浏览型号FM24C02的Datasheet PDF文件第9页浏览型号FM24C02的Datasheet PDF文件第11页浏览型号FM24C02的Datasheet PDF文件第12页浏览型号FM24C02的Datasheet PDF文件第13页浏览型号FM24C02的Datasheet PDF文件第14页  
Refer the following table for Slave Addresses string details:  
Acknowledge  
The FM24C04U/05U device will always respond with an acknowl-  
edge after recognition of a start condition and its slave address. If  
both the device and a write operation have been selected, the  
FM24C04U/05U will respond with an acknowledge after the  
receipt of each subsequent eight bit byte.  
Device  
A0 A1 A2 Page Page Block  
Blocks Addresses  
FM24C04U/05U  
P
A
A
2
0, 1  
A: Refers to a hardware configured Device Address pin.  
P: Refers to an internal PAGE BLOCK.  
In the read mode the FM24C04U/05U slave will transmit eight bits  
of data, release the SDA line and monitor the line for an acknowl-  
edge. If an acknowledge is detected, FM24C04U/05U will continue  
totransmitdata.Ifanacknowledgeisnotdetected,FM24C04U/05U  
will terminate further data transmissions and await the stop condi-  
tion to return to the standby power mode.  
All IIC EEPROMs use an internal protocol that defines a PAGE  
BLOCK size of 2K bits (for Word addresses 0x00 through 0xFF).  
Therefore, address bits A0, A1, or A2 (if designated 'P') are used  
to access a PAGE BLOCK in conjunction with the Word address  
used to access any individual data byte.  
Device Addressing  
The last bit of the slave address defines whether a write or read  
condition is requested by the master. A '1' indicates that a read  
operation is to be executed, and a '0' initiates the write mode.  
Following a start condition the master must output the address of  
the slave it is accessing. The most significant four bits of the slave  
address are those of the device type identifier. This is fixed as  
1010 for all EEPROM devices.  
A simple review: After the FM24C04U/05U recognizes the start  
condition, the devices interfaced to the IIC bus wait for a slave  
address to be transmitted over the SDA line. If the transmitted  
slave address matches an address of one of the devices, the  
designated slave pulls the SDA line LOW with an acknowledge  
signal and awaits further transmissions.  
Device Type  
Identifier  
Device  
Address  
1
0
1
0
A2  
A1  
A0 R/W (LSB)  
Page  
24C04/05  
Block Address  
10  
www.fairchildsemi.com  
FM24C04U/05U Rev. A.3  
 复制成功!