AD8132
DIN TO OUT SPECIFICATIONS
At TA = 25°C, VS = 5 V, VOCM = 2.5 V, G = 1, RL, dm = 499 Ω, RF = RG = 348 Ω, unless otherwise noted. For G = 2, RL, dm = 200 Ω, RF = 1000 Ω,
RG = 499 Ω. Refer to Figure 56 and Figure 57 for test setup and label descriptions. All specifications refer to single-ended input and
differential outputs, unless otherwise noted.
Table 3.
Parameter
Conditions
Min Typ
Max Unit
DYNAMIC PERFORMANCE
−3 dB Large Signal Bandwidth
VOUT = 2 V p-p
VOUT = 2 V p-p, G = 2
VOUT = 0.2 V p-p
VOUT = 0.2 V p-p, G = 2
VOUT = 0.2 V p-p
VOUT = 0.2 V p-p, G = 2
VOUT = 2 V p-p
250
300
180
360
155
65
50
1000
20
MHz
MHz
MHz
MHz
MHz
MHz
V/μs
ns
−3 dB Small Signal Bandwidth
Bandwidth for 0.1 dB Flatness
Slew Rate
Settling Time
Overdrive Recovery Time
NOISE/HARMONIC PERFORMANCE
Second Harmonic
800
0.1%, VOUT = 2 V p-p
VIN = 2.5 V to 0 V step, G = 2
5
ns
VOUT = 2 V p-p, 1 MHz, RL, dm = 800 Ω
VOUT = 2 V p-p, 5 MHz, RL, dm = 800 Ω
VOUT = 2 V p-p, 20 MHz, RL, dm = 800 Ω
VOUT = 2 V p-p, 1 MHz, RL, dm = 800 Ω
VOUT = 2 V p-p, 5 MHz, RL, dm = 800 Ω
VOUT = 2 V p-p, 20 MHz, RL, dm = 800 Ω
20 MHz, RL, dm = 800 Ω
−97
−100
−74
−100
−99
−67
−76
40
dBc
dBc
dBc
dBc
dBc
dBc
dBc
dBm
Third Harmonic
IMD
IP3
20 MHz, RL, dm = 800 Ω
Input Voltage Noise (RTI)
Input Current Noise
Differential Gain Error
Differential Phase Error
INPUT CHARACTERISTICS
Offset Voltage (RTI)
f = 0.1 MHz to 100 MHz
f = 0.1 MHz to 100 MHz
NTSC, G = 2, RL, dm = 150 Ω
NTSC, G = 2, RL, dm = 150 Ω
8
1.8
0.025
0.15
nV/√Hz
pA/√Hz
%
Degrees
VOS, dm = VOUT, dm/2; VDIN+ = VDIN− = VOCM = 2.5 V
TMIN to TMAX variation
1.0
3.5 mV
6
3
10
3
μV/°C
μA
MΩ
MΩ
pF
Input Bias Current
Input Resistance
7
Differential
Common-mode
Input Capacitance
Input Common-Mode Voltage
CMRR
1
0.3 to 3.0
−70
V
dB
ΔVOUT, dm/ΔVIN, cm; ΔVIN, cm = 1 V; resistors matched to 0.01%
Maximum ΔVOUT; single-ended output
−60
OUTPUT CHARACTERISTICS
Output Voltage Swing
Output Current
1.0 to 4.0
50
−68
V
mA
dB
Output Balance Error
ΔVOUT, cm/ΔVOUT, dm; ΔVOUT, dm = 1 V
Rev. F | Page 5 of 32
ADI [ ADI ]
