TMDS361
SLLS919–DECEMBER 2008............................................................................................................................................................................................ www.ti.com
DEVICE POWER
The TMDS361 is designed to operate from a single 3.3-V supply voltage. The TMDS361 has three power modes
of operation. These three modes are referred to as normal mode, standby mode, and low-power mode.
Normal mode is designed to be used during typical operating conditions. In normal mode, the device is fully
functional and consumes the greatest amount of power.
Standby mode is designed to be used when reduced power is desired, but DDC and HPD communication must
be maintained. Standby mode can be enabled via the I2C interface (See Table 8 through Table 11). or GPIO
interface (See Table 1). In standby mode, the high-speed TMDS data and clock channels are disabled to reduce
power consumption. The internal I2C logic and DDC function normally. HPD[1:3] follow HPD_SINK.
Low-power mode is designed to consume the least possible amount of power while still applying 3.3 V to the
device. Low-power mode can be enabled by either the LP pin or by local I2C (See Table 8 through Table 11). In
low-power mode, all of the inputs and outputs are disabled with the exception of the internal I2C logic and LP pin.
The clock-detect feature in the TMDS361 provides an automatic power-management feature in normal mode. if
no valid TMDS clock is detected, the terminations on the input TMDS data lines are disconnected, and the TMDS
outputs are high-Z. As soon as a valid TMDS clock is detected, the terminations on the TMDS data lines are
connected, the TMDS outputs come out of high-Z, and the device is fully functional and consumes the greatest
amount of power.
ELECTRICAL CHARACTERISTICS
over recommended operating conditions (unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
TYP MAX UNIT
ICC
Normal-mode supply current
LP = HIGH TMDS: VID(pp) = 1200 mV, 3 Gbps TMDS data
pattern; HPD_SINK = HIGH, S1/S2 = LOW/LOW, LOW/HIGH,
HIGH/HIGH
170
216
mA
ISTBY
Standby supply current
LP = HIGH, TMDS: VID(pp) = 1200 mV, 3 Gbps TMDS data
pattern; HPD_SINK = HIGH, S1 = HIGH, S2 = LOW
3
5.5
mA
ISD
Shutdown current
LP = LOW
300
12
555
18
µA
Normal-mode supply current,
with no active TMDS input cloc LOW/LOW, LOW/HIGH, HIGH/HIGH
LP = HIGH, No TMDS input clock, HPD_SINK =HIGH, S1/S2 =
INCLK
mA
HOT-PLUG DETECT
The TMDS361 is designed to support the hot-plug indication to the input ports (HDMI/DVI sources connected to
TMDS361) via the HPD[1:3] output pins. The state of the hot-plug output of the selected source follows the state
of the hot-plug input (HPD_SINK input pin) from the sink side. The state of the hot-plug output for the
non-selected source goes low (See Table 1).
The maximum VOH of the HPD depends on VCC. It is recommended that if VOH greater than 3.6 V is needed on
HPD, then an external circuit can be used to drive the VOH off of the +5 V from the HDMI source connected (as
shown in Figure 33).
ELECTRICAL CHARACTERISTICS
over recommended operating conditions (unless otherwise noted)
PARAMETER
High-level output voltage
Low-level output voltage
High-level input current
Low-level input current
Output source impedance
TEST CONDITIONS
IOH = 100 µA
MIN TYP
MAX UNIT
VOH(HPD)
2
VCC
0.4
V
V
VOL(HPD)
IOL = 100 µA
0
IH
IL
VIH = 2 V, VCC = 3.6 V
VIL = 0.8 V, VCC = 3.6 V
–10
10
µA
µA
Ω
–10
10
RL
800 1000
1200
10
Submit Documentation Feedback
Copyright © 2008, Texas Instruments Incorporated
Product Folder Link(s) :TMDS361
TI [ TEXAS INSTRUMENTS ]
