欢迎访问ic37.com |
会员登录 免费注册
发布采购

MSP430G2755IDA38 参数 Datasheet PDF下载

MSP430G2755IDA38图片预览
型号: MSP430G2755IDA38
PDF下载: 下载PDF文件 查看货源
内容描述: 混合信号微控制器 [MIXED SIGNAL MICROCONTROLLER]
分类和应用: 微控制器
文件页数/大小: 72 页 / 1004 K
品牌: TI [ TEXAS INSTRUMENTS ]
 浏览型号MSP430G2755IDA38的Datasheet PDF文件第9页浏览型号MSP430G2755IDA38的Datasheet PDF文件第10页浏览型号MSP430G2755IDA38的Datasheet PDF文件第11页浏览型号MSP430G2755IDA38的Datasheet PDF文件第12页浏览型号MSP430G2755IDA38的Datasheet PDF文件第14页浏览型号MSP430G2755IDA38的Datasheet PDF文件第15页浏览型号MSP430G2755IDA38的Datasheet PDF文件第16页浏览型号MSP430G2755IDA38的Datasheet PDF文件第17页  
MSP430G2955  
MSP430G2855  
MSP430G2755  
www.ti.com  
SLAS800 MARCH 2013  
Calibration Data Stored in Information Memory Segment A  
Calibration data is stored for both the DCO and for ADC10 organized in a tag-length-value (TLV) structure.  
Table 10. Tags Used by the Devices  
NAME  
ADDRESS  
0x10F6  
0x10DA  
-
VALUE  
0x01  
DESCRIPTION  
DCO frequency calibration at VCC = 3 V and TA = 30°C at calibration  
ADC10_1 calibration tag  
TAG_DCO_30  
TAG_ADC10_1  
TAG_EMPTY  
0x10  
0xFE  
Identifier for empty memory areas  
Table 11. Labels Used by the Devices  
ADDRESS  
LABEL  
SIZE  
CONDITION AT CALIBRATION AND DESCRIPTION  
OFFSET  
0x0010  
0x000E  
0x000C  
0x000A  
0x0008  
0x0006  
0x0004  
0x0002  
0x0009  
0x0008  
0x0007  
0x0006  
0x0005  
0x0004  
0x0003  
0x0002  
CAL_ADC_25T85  
CAL_ADC_25T30  
word  
word  
word  
word  
word  
word  
word  
word  
byte  
byte  
byte  
byte  
byte  
byte  
byte  
byte  
INCHx = 0x1010, REF2_5 = 1, TA = 85°C  
INCHx = 0x1010, REF2_5 = 1, TA = 30°C  
CAL_ADC_25VREF_FACTOR  
CAL_ADC_15T85  
REF2_5 = 1, TA = 30°C, IVREF+ = 1 mA  
INCHx = 0x1010, REF2_5 = 0, TA = 85°C  
CAL_ADC_15T30  
INCHx = 0x1010, REF2_5 = 0, TA = 30°C  
CAL_ADC_15VREF_FACTOR  
CAL_ADC_OFFSET  
CAL_ADC_GAIN_FACTOR  
CAL_BC1_1MHZ  
REF2_5 = 0, TA = 30°C, IVREF+ = 0.5 mA  
External VREF = 1.5 V, fADC10CLK = 5 MHz  
External VREF = 1.5 V, fADC10CLK = 5 MHz  
-
-
-
-
-
-
-
-
CAL_DCO_1MHZ  
CAL_BC1_8MHZ  
CAL_DCO_8MHZ  
CAL_BC1_12MHZ  
CAL_DCO_12MHZ  
CAL_BC1_16MHZ  
CAL_DCO_16MHZ  
Brownout  
The brownout circuit is implemented to provide the proper internal reset signal to the device during power on and  
power off.  
Digital I/O  
Four 8-bit I/O ports are implemented:  
All individual I/O bits are independently programmable.  
Any combination of input, output, and interrupt condition (port P1 and port P2 only) is possible.  
Edge-selectable interrupt input capability for all bits of port P1 and port P2.  
Read and write access to port-control registers is supported by all instructions.  
Each I/O has an individually programmable pullup or pulldown resistor.  
Each I/O has an individually programmable pin oscillator enable bit to enable low-cost touch sensing.  
Watchdog Timer (WDT+)  
The primary function of the watchdog timer (WDT+) module is to perform a controlled system restart after a  
software problem occurs. If the selected time interval expires, a system reset is generated. If the watchdog  
function is not needed in an application, the module can be disabled or configured as an interval timer and can  
generate interrupts at selected time intervals.  
Copyright © 2013, Texas Instruments Incorporated  
Submit Documentation Feedback  
13  
Product Folder Links: MSP430G2955 MSP430G2855 MSP430G2755