MSP430F663x
SLAS566C –JUNE 2010–REVISED AUGUST 2012
www.ti.com
Low-Power Mode Supply Currents (Into VCC) Excluding External Current (continued)
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)(1)(2)
-40°C
TYP MAX
25°C
TYP MAX
60°C
TYP MAX
85°C
TYP MAX
PARAMETER
VCC
PMMCOREVx
UNIT
Low-power mode 4.5
(LPM4.5)(12)
ILPM4.5
3 V
0.2
0.3
0.6
0.7
0.9
1.4
µA
(12) Internal regulator disabled. No data retention.
CPUOFF = 1, SCG0 = 1, SCG1 = 1, OSCOFF = 1, PMMREGOFF = 1 (LPM4.5); fDCO = fACLK = fMCLK = fSMCLK = 0 MHz
Low-Power Mode With LCD Supply Currents (Into VCC) Excluding External Current
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)(1)
(2)
Temperature (TA)
PARAMETER
VCC
PMMCOREVx
-40°C
TYP MAX
2.3
25°C
TYP MAX
2.7 3.1
60°C
TYP MAX
5.4
85°C
TYP MAX
7.4
UNIT
0
1
2
3
0
1
2
3
0
1
2
0
1
2
3
11.5
Low-power mode 3
(LPM3) current, LCD 4-
mux mode, external
biasing(3) (4)
ILPM3,
LCD,
ext. bias
2.3
2.4
2.4
2.7
2.7
2.8
2.8
2.7
2.8
2.8
3.2
3.2
3.3
3.3
3.8
3.9
4.0
4.0
4.1
4.2
4.2
5.6
5.8
5.9
5.9
6.1
6.2
6.4
7.5
7.7
7.9
7.9
8.1
8.3
8.4
3 V
µA
3.5
3.8
13.2
12.2
Low-power mode 3
(LPM3) current, LCD 4-
mux mode, internal
biasing, charge pump
disabled(3)(5)
ILPM3,
LCD,
int. bias
3 V
2.2 V
3 V
µA
µA
µA
4.9
13.7
Low-power mode 3
(LPM3) current, LCD 4-
mux mode, internal
biasing, charge pump
enabled(3)(6)
ILPM3
LCD,CP
(1) All inputs are tied to 0 V or to VCC. Outputs do not source or sink any current.
(2) The currents are characterized with a Micro Crystal CC4V-T1A SMD crystal with a load capacitance of 9 pF. The internal and external
load capacitance are chosen to closely match the required 9 pF.
(3) Current for watchdog timer clocked by ACLK and RTC clocked by LFXT1 (32768 Hz) included. ACLK = low frequency crystal operation
(XTS = 0, XT1DRIVEx = 0).
CPUOFF = 1, SCG0 = 1, SCG1 = 1, OSCOFF = 0 (LPM3); fACLK = 32768 Hz, fMCLK = fSMCLK = fDCO = 0 MHz
Current for brownout included. Low side supervisor and monitors disabled (SVSL, SVML). High side supervisor and monitor disabled
(SVSH, SVMH). RAM retention enabled.
(4) LCDMx = 11 (4-mux mode), LCDREXT = 1, LCDEXTBIAS = 1 (external biasing), LCD2B = 0 (1/3 bias), LCDCPEN = 0 (charge pump
disabled), LCDSSEL = 0, LCDPREx = 101, LCDDIVx = 00011 (fLCD = 32768 Hz/32/4 = 256 Hz)
Current through external resistors not included (voltage levels are supplied by test equipment).
Even segments S0, S2,... = 0, odd segments S1, S3,... = 1. No LCD panel load.
(5) LCDMx = 11 (4-mux mode), LCDREXT = 0, LCDEXTBIAS = 0 (internal biasing), LCD2B = 0 (1/3 bias), LCDCPEN = 0 (charge pump
disabled), LCDSSEL = 0, LCDPREx = 101, LCDDIVx = 00011 (fLCD = 32768 Hz/32/4 = 256 Hz)
Even segments S0, S2,... = 0, odd segments S1, S3,... = 1. No LCD panel load.
(6) LCDMx = 11 (4-mux mode), LCDREXT = 0, LCDEXTBIAS = 0 (internal biasing), LCD2B = 0 (1/3 bias), LCDCPEN = 1 (charge pump
enabled), VLCDx = 1000 (VLCD = 3 V, typ.), LCDSSEL = 0, LCDPREx = 101, LCDDIVx = 00011 (fLCD = 32768 Hz/32/4 = 256 Hz)
Even segments S0, S2,... = 0, odd segments S1, S3,... = 1. No LCD panel load.
Schmitt-Trigger Inputs – General Purpose I/O(1)
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
PARAMETER
TEST CONDITIONS
VCC
1.8 V
3 V
MIN
0.80
1.50
TYP
MAX UNIT
1.40
V
VIT+
Positive-going input threshold voltage
2.10
(1) Same parametrics apply to clock input pin when crystal bypass mode is used on XT1 (XIN) or XT2 (XT2IN).
50
Copyright © 2010–2012, Texas Instruments Incorporated
TI [ TEXAS INSTRUMENTS ]
