欢迎访问ic37.com |
会员登录 免费注册
发布采购

78Q2123CGV/F 参数 Datasheet PDF下载

78Q2123CGV/F图片预览
型号: 78Q2123CGV/F
PDF下载: 下载PDF文件 查看货源
内容描述: 10 / 100BASE -TX收发器 [10/100BASE-TX Transceiver]
分类和应用: 网络接口电信集成电路电信电路局域网(LAN)标准以太网:16GBASE-T
文件页数/大小: 42 页 / 730 K
品牌: TERIDIAN [ TERIDIAN SEMICONDUCTOR CORPORATION ]
 浏览型号78Q2123CGV/F的Datasheet PDF文件第4页浏览型号78Q2123CGV/F的Datasheet PDF文件第5页浏览型号78Q2123CGV/F的Datasheet PDF文件第6页浏览型号78Q2123CGV/F的Datasheet PDF文件第7页浏览型号78Q2123CGV/F的Datasheet PDF文件第9页浏览型号78Q2123CGV/F的Datasheet PDF文件第10页浏览型号78Q2123CGV/F的Datasheet PDF文件第11页浏览型号78Q2123CGV/F的Datasheet PDF文件第12页  
78Q2123/78Q2133
MicroPHY™
10/100BASE-TX Transceiver
MII (MEDIA INDEPENDENT INTERFACE) (CONTINUED)
SIGNAL
RX_DV
PIN
11
TYPE DESCRIPTION
COZ
RECEIVE DATA VALID: RX_DV is asserted high to indicate that valid data is
present on the RXD[3:0] pins. In 100BASE-TX mode, it transitions high with the first
nibble of the preamble and is pulled low when the last data nibble has been
received. In 10BASE-T mode it transitions high when the start-of-frame delimiter
(SFD) is detected. This pin is tri-stated in isolate mode.
RECEIVE DATA: Received data is provided to the MAC via RXD[3:0]. These pins
are tri-stated in isolate mode.
RECEIVE ERROR: RX_ER is asserted high when an error is detected during frame
reception. In PCS bypass mode, this pin becomes the MSB of the receive 5-bit code
group. This pin is tri-stated in isolate mode.
MANAGEMENT DATA CLOCK: MDC is the clock used for transferring data via the
MDIO pin.
MANAGEMENT DATA INPUT/OUTPUT: MDIO is a bi-directional port used to
access management registers within the 78Q2123/78Q2133. This pin requires an
external pull-up resistor as specified in IEEE-802.3.
RXD[3:0]
RX_ER
[5:8]
13
COZ
COZ
MDC
MDIO
2
1
CIS
CIO
CONTROL AND STATUS
SIGNAL
RST
PIN
23
TYPE DESCRIPTION
CIS
ACTIVE LOW RESET: When pulled low the pin resets the chip. The reset pulse
must be long enough to guarantee stabilization of the supply voltage and startup of
the oscillator. Refer to the Electrical Specifications for the reset pulse requirements.
There are 2 other ways to reset the chip:
i. Through the internal power-on-reset (activated when the chip is being powered
up)
ii. Through the MII register bit (MR 0.15)
INTR
32
COZ
INTERRUPT PIN: This pin is used to signal an interrupt to the media access
controller. The pin is held in the high impedance state when an interrupt is not
indicated. The pin will be forced high or low to signal an interrupt depending upon
the value of the INPOL bit (MR16.14). The events which trigger an interrupt can be
programmed via the Interrupt Control Register located at address MR17.
Page: 8 of 42
©
2009 Teridian Semiconductor Corporation
Rev 1.5