欢迎访问ic37.com |
会员登录 免费注册
发布采购

71M6521BE 参数 Datasheet PDF下载

71M6521BE图片预览
型号: 71M6521BE
PDF下载: 下载PDF文件 查看货源
内容描述: 电能计量IC [Energy Meter IC]
分类和应用:
文件页数/大小: 97 页 / 1586 K
品牌: TERIDIAN [ TERIDIAN SEMICONDUCTOR CORPORATION ]
 浏览型号71M6521BE的Datasheet PDF文件第36页浏览型号71M6521BE的Datasheet PDF文件第37页浏览型号71M6521BE的Datasheet PDF文件第38页浏览型号71M6521BE的Datasheet PDF文件第39页浏览型号71M6521BE的Datasheet PDF文件第41页浏览型号71M6521BE的Datasheet PDF文件第42页浏览型号71M6521BE的Datasheet PDF文件第43页浏览型号71M6521BE的Datasheet PDF文件第44页  
71M6521BE  
Energy Meter IC  
DATA SHEET  
JANUARY 2008  
DIO_DIR [n]  
0
1
DIO Pin n Function  
Input  
Output  
Table 54: DIO_DIR Control Bit  
Additionally, if DIO6 is declared an output, it can be configured as dedicated pulse output (WPULSE = DIO6) using the  
DIO_PW register. In this case, DIO6 is under CE control. DIO4 and DIO5 can be configured to implement the EEPROM  
Interface.  
The PB pin is a dedicated digital input. If the optical UART is not used, OPT_TX and OPT_RX can be configured as dedicated  
DIO pins (DIO1, DIO2, see Optical Interface section).  
A 3-bit configuration word, I/O RAM register, DIO_Rx (0x2009[2:0] through 0x200E[6:4]) can be used for certain pins, when  
configured as DIO, to individually assign an internal resource such as an interrupt or a timer control (see Table 55 for DIO pins  
available for this option). This way, DIO pins can be tracked even if they are configured as outputs.  
Tracking DIO pins configured as outputs is useful for pulse counting without external hardware.  
When driving LEDs, relay coils etc., the DIO pins should sink the current into GNDD (as shown in Figure 8,  
right), not source it from V3P3D (as shown in Figure 8, left). This is due to the resistance of the internal  
switch that connects V3P3D to either V3P3SYS or VBAT.  
When configured as inputs, the dual-function (DIO/SEG) pins should not be pulled above V3P3SYS in  
MISSION and above VBAT in LCD and BROWNOUT modes. Doing so will distort the LCD waveforms of the  
other pins. This limitation applies to any pin that can be configured as a LCD driver.  
71M6521B  
71M6521B  
V3P3SYS  
V3P3SYS  
VBAT  
3.3V  
3.3V  
VBAT  
LED  
V3P3D  
V3P3D  
DIO1  
DIO1  
R
LED  
R
DGND  
DGND  
Not recommended  
Recommended  
Figure 8: Connecting an External Load to DIO Pins  
The PB pin is a dedicated digital input. In addition, if the optical UART is not used, OPT_TX and OPT_RX can be configured  
as dedicated DIO pins DIO1 and DIO2. Thus, in addition to the 12 general-purpose DIO pins (DIO4…DIO11, DIO14…DIO17),  
there are three additional pins that can be used for digital input and output.  
Page: 40 of 97  
© 2005-2008 TERIDIAN Semiconductor Corporation  
V1.0