BM28723AMUV
Register Map
Address
0x01
Initial Value
Recommended value
0x00(Note 22)
Description
Function
0xE0
RAM clear
Bypass
RAM clear setting
0x02
0x03
0x06
0x07
0x08
0x09
0x0A
0x0B
0x00
0x00
0x02
0x20
0x8A
0x00
-
Select bypass blocks
0x02
Digital audio input 1
I2S input format setting
0x20
Synchronous error 2
Synchronous error setting
LRCLK stop detection setting
BCLK stop detection setting
Read/Clear stop detection
0x8A
LRCLK,BCLK stop detection 1
LRCLK,BCLK stop detection 2
LRCLK,BCLK stop detection 3
0x00
Read/Write Only
0x20
0x20
0x20
BCLK Measurement of velocity 1 BCLK fast detection setting
BCLK Measurement of velocity 2 BCLK slow detection setting
0x20
0x00 (48kHz sampling)
0x0C
0x00
Sampling frequency setting
Sampling frequency setting
(Note 22)
0x0D
0x0E
0x00
0x40(Note 22)
0x00(Note 22)
Auto return 1
Auto return 2
Auto return setting
Auto return monitor
Read Only
Fine volume setting/
Independent volume setting
Lch/dependent Volume setting
(0dB: 0x30)
Rch volume setting
(0dB: 0x30)
0x10
0x11
0x12
0x13
0x00
0xFF
0xFF
0x60
0x00
0xFF
0xFF
0x60
Volume, Balance, Post-scaler 1
Volume, Balance, Post-scaler 2
Volume, Balance, Post-scaler 3
Volume, Balance, Post-scaler 4
Post-scaler setting
(0dB: 0x60)
0x14
0x15
0x88
0x03
0x88
0x00
Volume, Balance, Post-scaler 5
Mute function
L/R fine postscaler setting
Mute transition time setting
Pre-Scaler setting
(0dB: 0x60)
0x16
0x60
0x60
Pre-Scaler
0x17
0x18
0x1A
0x1B
0x20
0x21
0x28
0x29
0x2A
0x2B
0x2C
0x2E
0x2F
0x12
0x01
0x01
0xE1
0xFC
0xC0
0x40
0x80
0x3B
0x13
0x40
0x3B
0x13
0x12
0x01
0x01
0xE1
0xFC
0xC0
0x40
0x80
0x3B
0x13
0x40
0x3B
0x13
Channel mixer
Channel mixer setting
DC cut HPF setting
DC Cut HPF
Hard Clipper 1
Hard Clipper setting
Hard Clipper 2
Hard Clip level setting
DRC select setting
DRC common 1
DRC common 2
Transition form setting
Threshold setting
AGC_TH1 setting of DRC1
Slope (α) setting of DRC1
RATE setting of DRC1
TIME setting of DRC1
AGC_TH2 setting of DRC1
RATE setting of DRC1
TIME setting of DRC1
Slope setting
A_RATE and R_RATE setting
A_TIME and R_TIME setting
Threshold setting
A_RATE and R_RATE setting
A_TIME and R_TIME setting
(Note 22) It must be set at the time of start-up. Refer to P.62 “20. The wake-up Procedure of power-up”.
www.rohm.com
TSZ02201-0C1C0E900720-1-2
31.Aug.2018 Rev.001
© 2018 ROHM Co., Ltd. All rights reserved.
65/79
TSZ22111 • 15 • 001