BM28723AMUV
Application Circuit Example2 (Stereo BTL output, RL=8Ω, 22V<VCCP1, VCCP2≤24V)
μ-con
L25
15μH
GNDP1
DVDD DVDD
10μF
C27
3.3μF
C26
10kΩ
R31
10kΩ
R32
680pF
C25B
32
31
30
29
28
27
26
25
REG_G BSP1P OUT1P
NC
5.6Ω
R25
0.47μF
SP ch1
(Lch)
C25A
I2C BUS
Address
Select
REG_G
DVDD
VSS
GNDP1
VCCP1
Control
I/F
1
2
3
4
5
6
7
8
2 wire I/F
24
23
22
21
20
19
18
17
ADDR
VCCP1
10μF
C24
Driver
FET 1P
0.47μF
C21A
BCLK
5.6Ω
BCLK
LRCLK
SDATA
R2 0Ω
R21
GNDP1
BSP1N
GNDP1
680pF
I2S/LJ/RJ
I/F
C21B
LRCLK
Driver
FET 1N
Digital
Audio
Source
R3 0Ω
3.3μF
C22
15μH
L21
SDATA
8 Times
Over-
Sampling
Digital
Filter
OUT1N
OUT2P
R40Ω
PWM
Modulator
Audio
DSP
TEST1
VSS
R6
L20
15μH
C19
3.3μF
C6B
0.027μF
Driver
FET 2P
1.5kΩ
PLL
BSP2P
PLL
C20B
VSS
C6A
2700pF
680pF
C7
GNDP2
R20
5.6Ω
REG15
VSS
REG15
C20A
0.47μF
Driver
FET 2N
1μF
GNDP2
VCCP2
C17
10μF
Protection
VSS
LRCLK
VCCP2
DGND
GNDP2
BCLK
SP ch2
(Rch)
DVDD
C16A
0.47μF
TEST2
TEST3SDATAO
R16
5.6Ω
BSP2N OUT2N
15 16
NC
14
9
10
11
12
13
C16B
680pF
C15
3.3μF
0Ω
R12
R13
VSS
VSS
1μF
C10
VSS
L16
DVDD(3.3V)
15μH
μ-con
10kΩ
DVDD
SDATAO
ERRORX
Figure 71
Parts
Qty
4
Parts No.
Description
Inductor
L16, L20, L21, L25
15μH / 2.9A / (±20%)
1.5kΩ / 1/16W / F(±1%)
10kΩ / 1/16W / J(±5%)
0Ω / 1/10W / J(±5%)
1
R6
R31, R32
R2, R3, R4, R12
R16, R20, R21, R25
R13
2
Resistor
4
4
5.6Ω / 1/4W / J(±5%)
10kΩ / 1/16W / J(±5%)
2700pF / 6.3V / B(±10%)
0.027μF / 6.3V / B(±10%)
1
1
C6A
1
C6B
C16B, C20B,
C21B, C25B
C16A, C20A,
C21A, C25A
4
680pF / 50V / CH(±5%)
4
2
4
0.47μF / 50V / B(±10%)
10μF / 35V / B(±10%)
3.3μF / 16V / B(±10%)
Capacitor
C17, C24
C15, C19,
C22, C26
2
1
C7, C10
C27
1.0μF / 10V / B(±10%)
10μF / 16V / B(±10%)
Caution 1: If the impedance characteristics of the speakers at high-frequency range increase rapidly, the LSI might not have stable operation in the resonance
frequency range of the LC filter. Therefore, consider adding damping-circuit, etc., depending on the impedance of the speaker.
Caution 2: Though this LSI has a short protection function, when short to VCC or GND after the LC filter, over-current occurs during short protection function
operation. Be careful about over/undershoot which exceeds the maximum standard ratings because back electromotive force of the inductor will occur
which sometimes leads to LSI destruction.
The Inductor must be used to the coil with large margin of rated DC current (saturation current). When the short-circuit of the speaker output (after the
LC filter) to VCC or GND occurs when the coil with small rated DC current is used, LSI destruction might be caused. Because the coil causes the magnetic
saturation behavior, it instantaneously passes the heavy-current to LSI.
Caution 3: Overshoot of output PWM differs according to the board or coupling capacitor of VCC, and etc. Check to ensure that it is lower than absolute maximum
ratings.
If it exceeds the absolute maximum ratings, snubber circuit must need to be added.
Caution 4: When it is used at VCCP1, VCCP2>22V, snubber circuit must need to be added, and must change LC filter value to suppress the influence of the LCR
resonance.
Caution 5: This circuit constant is value with ROHM evaluation board, and adjustment of the constant may be necessary for the application board. Must carry out
enough evaluations.
www.rohm.com
TSZ02201-0C1C0E900720-1-2
© 2018 ROHM Co., Ltd. All rights reserved.
69/79
TSZ22111 • 15 • 001
31.Aug.2018 Rev.001