欢迎访问ic37.com |
会员登录 免费注册
发布采购

HYB18M256320CF-6/7.5 参数 Datasheet PDF下载

HYB18M256320CF-6/7.5图片预览
型号: HYB18M256320CF-6/7.5
PDF下载: 下载PDF文件 查看货源
内容描述: DRAM的移动应用程序 [DRAMs for Mobile Applications]
分类和应用: 动态存储器
文件页数/大小: 26 页 / 1614 K
品牌: QIMONDA [ QIMONDA AG ]
 浏览型号HYB18M256320CF-6/7.5的Datasheet PDF文件第14页浏览型号HYB18M256320CF-6/7.5的Datasheet PDF文件第15页浏览型号HYB18M256320CF-6/7.5的Datasheet PDF文件第16页浏览型号HYB18M256320CF-6/7.5的Datasheet PDF文件第17页浏览型号HYB18M256320CF-6/7.5的Datasheet PDF文件第19页浏览型号HYB18M256320CF-6/7.5的Datasheet PDF文件第20页浏览型号HYB18M256320CF-6/7.5的Datasheet PDF文件第21页浏览型号HYB18M256320CF-6/7.5的Datasheet PDF文件第22页  
Internet Data Sheet  
HY[B/E]18M256[16/32]0CF  
256-Mbit DDR Mobile-RAM  
17) tDQSQ consists of data pin skew and output pattern effects, and p-channel to n-channel variation of the output drivers for any given cycle.  
18) The specific requirement is that DQS be valid (HIGH, LOW, or some point on a valid transition) on or before this CK edge. A valid transition  
is defined as monotonic and meeting the input slew rate specifications of the device. When no writes were previously in progress on the  
bus, DQS will be transitioning from Hi-Z to logic LOW. If a previous write was in progress, DQS could be HIGH, LOW, or transitioning from  
HIGH to LOW at this time, depending on tDQSS  
.
19) The maximum limit for this parameter is not a device limit. The device operates with a greater value for this parameter, but system  
performance (bus turnaround) will degrade accordingly.  
20) A low level on DQS may be maintained during High-Z states (DQS drivers disabled) by adding a weak pull-down element in the system.  
It is recommended to turn off the weak pull-down element during read and write bursts (DQS drivers enabled).  
21) These parameters account for the number of clock cycles and depend on the operating frequency, as follows:no. of clock cycles = specified  
delay / clock period; round to the next higher integer.  
22) tDAL = (tWR / tCK) + (tRP / tCK): for each of the terms above, if not already an integer, round to the next higher integer.  
23) tWTR is also referred to as tCDLR  
24) A maximum of eight AUTOREFRESH commands can be posted to the DDR Mobile-RAM device, meaning that the maximum absolute  
interval between any Refresh command and the next Refresh command is 8 * tREFI  
.
FIGURE 3  
Measurement with Reference Load  
)ꢊ/  
:
ꢋ ꢃꢂ /HMS  
ꢁꢂ P&  
TABLE 12  
AC Overshoot / Undershoot Specification  
Parameter  
Max.  
Unit  
Note  
Maximum peak amplitude allowed for overshoot  
Maximum peak amplitude allowed for undershoot  
Maximum overshoot area above VDD  
0.5  
0.5  
3.0  
3.0  
V
V
V-ns  
V-ns  
Maximum undershoot area below VSS  
FIGURE 4  
AC Overshoot and Undershoot Definition  
ꢅꢂꢃ  
ꢅꢂꢁ  
ꢄꢂꢃ  
ꢄꢂꢁ  
/VERSHOOT !REA  
6$$  
-AXꢂ !MPLITUDE ꢆ ꢁꢂꢃ6  
-AXꢂ !REA ꢆ ꢇ6ꢀNS  
ꢁꢂꢃ  
633  
ꢀꢁꢂꢃ  
5NDERSHOOT !REA  
4IME ꢈNSꢉ  
Rev.1.44, 2007-07  
18  
06262007-JK8G-48BV  
 复制成功!