NXP Semiconductors
PF4210
14-channel power management integrated circuit (PMIC) for audio/video applications
Symbol
Parameter
Min
Typ
Max
Unit
GEN5tON
Turn on time
µs
Enable to 90 % of end value, VIN3
=
60
—
500
VIN3MIN, 4.5 V
IGEN5 = 0.0 mA
GEN5tOFF
Turn off time
ms
Disable to 10 % of initial value, VIN3
VIN3MIN
=
—
—
10
IGEN5 = 0.0 mA
GEN5OSHT
Startup overshoot
%
%
VIN3 = VIN3MIN, 4.5 V, IGEN5 = 0.0 mA
—
—
1.0
—
2.0
3.0
VGEN5LOTR
Transient load response
VIN3 = VIN3MIN, 4.5 V
IGEN5 = 10 to 100 mA in 1.0 µs
Peak of overshoot or undershoot of VGEN5
with respect to final value. See Figure 30
VGEN5LITR
Transient line response
IGEN5 = 75 mA
mV
VIN3INITIAL = 2.8 V to VIN3FINAL = 3.3 V for
VGEN5[3:0] = 0000 to 0111
—
5.0
8.0
VIN3INITIAL = VGEN5 + 0.3 V to VIN3FINAL
= VGEN5 + 0.8 V for VGEN5[3:0] = 1000 to
1111
See Figure 30
[1] When the LDO output voltage is set above 2.6 V the minimum allowed input voltage need to be at least the output voltage plus 0.25 V for proper
regulation due to the dropout voltage generated through the internal LDO transistor.
[2] The PSRR of the regulators is measured with the perturbing signal at the input of the regulator. The power management IC is supplied separately from
the input of the regulator and does not contain the perturbed signal. During measurements, care must be taken not to operate in the dropout region of the
regulator under test. VIN3MIN refers to the minimum allowed input voltage for a particular output voltage.
10.4.6.5.6 VGEN6
Table 105.ꢀVGEN6 electrical characteristics
All parameters are specified at TMIN to TMAX (see Table 4), VIN = 3.6 V, VIN3 = 3.6 V, VGEN6[3:0] = 1111, IGEN6 = 10 mA,
typical external component values, unless otherwise noted. Typical values are characterized at VIN = 3.6 V, VIN3 = 3.6 V,
VGEN6[3:0] = 1111, IGEN6 = 10 mA, and 25 °C, unless otherwise noted.
Symbol
VGEN6
VIN3
Parameter
Min
Typ
Max
Unit
[1]
Operating input voltage
V
1.8 V ≤ VGEN6NOM ≤ 2.5 V
2.6 V ≤ VGEN6NOM ≤ 3.3 V
2.8
—
—
4.5
4.5
VGEN6NOM
+ 0.250
VGEN6NOM
IGEN6
Nominal output voltage
Operating load current
—
Table 91
—
—
V
0.0
200
mA
VGEN6 DC
VGEN6TOL
Output voltage tolerance
VIN3MIN < VIN3 < 4.5 V
%
−3.0
—
3.0
0.0 mA < IGEN6 < 200 mA
VGEN6[3:0] = 0000 to 1111
PF4210
All information provided in this document is subject to legal disclaimers.
© NXP B.V. 2018. All rights reserved.
Data sheet: technical data
Rev. 2.0 — 14 November 2018
98 / 137
NXP [ NXP ]
