欢迎访问ic37.com |
会员登录 免费注册
发布采购

PC28F128G18FF 参数 Datasheet PDF下载

PC28F128G18FF图片预览
型号: PC28F128G18FF
PDF下载: 下载PDF文件 查看货源
内容描述: 128MB, 256MB,512MB ,1GB的StrataFlash存储器 [128Mb, 256Mb, 512Mb, 1Gb StrataFlash Memory]
分类和应用: 存储
文件页数/大小: 118 页 / 1154 K
品牌: MICRON [ MICRON TECHNOLOGY ]
 浏览型号PC28F128G18FF的Datasheet PDF文件第39页浏览型号PC28F128G18FF的Datasheet PDF文件第40页浏览型号PC28F128G18FF的Datasheet PDF文件第41页浏览型号PC28F128G18FF的Datasheet PDF文件第42页浏览型号PC28F128G18FF的Datasheet PDF文件第44页浏览型号PC28F128G18FF的Datasheet PDF文件第45页浏览型号PC28F128G18FF的Datasheet PDF文件第46页浏览型号PC28F128G18FF的Datasheet PDF文件第47页  
128Mb, 256Mb, 512Mb, 1Gb StrataFlash Memory  
SUSPEND and RESUME Operations  
SUSPEND and RESUME Operations  
PROGRAM and ERASE operations of the main array can be suspended to perform other  
device operations, and then subsequently resumed. OTP area programming operations  
cannot be suspended. During erase suspend or program suspend, the addressed block  
must remain unlocked, VPP must be at VPPL or VPPH, and WP# must remain unchanged.  
Otherwise, the ERASE or PROGRAM operation will abort, setting the appropriate status  
register error bit(s).  
SUSPEND Operation  
To suspend an ongoing ERASE or PROGRAM operation, issue the SUSPEND command  
to any device address. Issuing the SUSPEND command does not change the read mode.  
Upon issuing a SUSPEND command, the ongoing ERASE or PROGRAM operation sus-  
pends after a delay of tSUSP. The operation is suspended only when SR[7:6] = 1 (erase  
suspend) or SR[7:2] = 1 (program suspend).  
While suspended, reading from a block that was being erased or programmed is not al-  
lowed. Also, programming within an erase suspended block is not allowed, and if at-  
tempted, will result in a programming error (SR[4] = 1). Erasing under program suspend  
is not allowed. However, array programming under erase suspend is allowed, and can  
also be suspended. This results in a simultaneous erase suspend and program suspend  
condition, indicated by SR[7:6,2] = 1. Additional valid commands while suspended are  
READ ARRAY, READ STATUS REGISTER, READ ID, READ CFI, CLEAR STATUS REGIS-  
TER, and RESUME. No other commands are allowed.  
During suspend, CE# may be de-asserted, placing the device in standby and reducing  
active current to standby levels. VPP must remain at VPPL or VPPH, and WP# must remain  
unchanged.  
Asserting RST# aborts any suspended BLOCK ERASE and PROGRAM operations; array  
contents at the addressed locations will be indeterminate.  
During suspend, CE# may be de-asserted. The device is placed in standby, reducing ac-  
tive current. VPP must remain at VPPL or VPPH, and WP# must remain unchanged.  
Asserting RST# aborts suspended BLOCK ERASE and PROGRAM operations; array con-  
tents at the addressed locations are indeterminate.  
Table 24: Valid Commands During Suspend  
Device Command  
Program Suspend  
Erase Suspend  
Read Array  
Allowed  
Allowed  
Allowed  
Allowed  
Allowed  
Allowed  
Allowed  
Allowed  
Allowed  
Allowed  
Allowed  
Read Status Register  
Clear Status Register  
Read Device Information  
CFI Query  
Word Program  
Not Allowed  
Not Allowed  
Not Allowed  
Not Allowed  
Buffered Program  
Buffered Enhanced Factory Program  
Block Erase  
Not Allowed  
Not Allowed  
Not Allowed  
PDF: 09005aef8448483a  
128_256_512_65nm_g18.pdf - Rev. F 8/11 EN  
Micron Technology, Inc. reserves the right to change products or specifications without notice.  
43  
© 2011 Micron Technology, Inc. All rights reserved.