MX29LV160C T/B
device then returns to reading array data and addresses
are no longer latched. The system can determine the
status of the program operation by using
Q7, Q6, or RY/BY#. See "Write Operation Status" for
information on these status bits.
During the Automatic Erase algorithm, Data# Polling pro-
duces a "0" on Q7.When the Automatic Erase algorithm
is complete, or if the device enters the Erase Suspend
mode, Data# Polling produces a "1" on Q7.This is analo-
gous to the complement/true datum output described for
the Automatic Program algorithm: the erase function
changes all the bits in a sector to "1" prior to this, the
device outputs the "complement,” or "0".” The system
must provide an address within any of the sectors se-
lected for erasure to read valid status information on Q7.
Any commands written to the device during the Embed-
ded Program Algorithm are ignored.Note that a hardware
reset immediately terminates the programming
operation.The Byte/Word Program command sequence
should be reinitiated once the device has reset to read-
ing array data, to ensure data integrity.
After an erase command sequence is written, if all sec-
tors selected for erasing are protected, Data# Polling on
Q7 is active for approximately 100 us, then the device
returns to reading array data. If not all selected sectors
are protected, the Automatic Erase algorithm erases the
unprotected sectors, and ignores the selected sectors
that are protected.
Programming is allowed in any sequence and across
sector boundaries. A bit cannot be programmed from a
"0" back to a "1". Attempting to do so may cause the
device to set Q5 to "1", or cause the Data# Polling algo-
rithm to indicate the operation was successful.However,
a succeeding read will show that the data is still "0".
Only erase operations can convert a "0" to a "1".
When the system detects Q7 has changed from the
complement to true data, it can read valid data at Q7-Q0
on the following read cycles. This is because Q7 may
change asynchronously with Q0-Q6 while Output Enable
(OE#) is asserted low.
WRITE OPERATION STATUS
The device provides several bits to determine the status
of a write operation: Q2, Q3, Q5, Q6, Q7, and RY/BY#.
Table 8 and the following subsections describe the func-
tions of these bits. Q7, RY/BY#, and Q6 each offer a
method for determining whether a program or erase op-
eration is complete or in progress. These three bits are
discussed first.
RY/BY# :Ready/Busy
The RY/BY# is a dedicated, open-drain output pin that
indicates whether an Automatic Erase/Program algorithm
is in progress or complete. The RY/BY# status is valid
after the rising edge of the final WE# or CE#, whichever
happens first, in the command sequence.Since RY/BY#
is an open-drain output, several RY/BY# pins can be tied
together in parallel with a pull-up resistor to Vcc.
Q7:Data# Polling
The Data# Polling bit, Q7, indicates to the host system
whether an Automatic Algorithm is in progress or com-
pleted, or whether the device is in Erase Suspend.Data#
Polling is valid after the rising edge of the finalWE# pulse
in the program or erase command sequence.
If the output is low (Busy), the device is actively erasing
or programming.(This includes programming in the Erase
Suspend mode.) If the output is high (Ready), the device
is ready to read array data (including during the Erase
Suspend mode), or is in the standby mode.
During the Automatic Program algorithm, the device out-
puts on Q7 the complement of the datum programmed to
Q7.This Q7 status also applies to programming during
Erase Suspend.When the Automatic Program algorithm
is complete, the device outputs the datum programmed
to Q7.The system must provide the program address to
read valid status information on Q7.If a program address
falls within a protected sector, Data# Polling on Q7 is
active for approximately 1 us, then the device returns to
reading array data.
Table 8 shows the outputs for RY/BY# during write op-
eration.
Q6:Toggle BIT I
Toggle Bit I on Q6 indicates whether an Automatic Pro-
gram or Erase algorithm is in progress or complete, or
whether the device has entered the Erase Suspend mode.
P/N:PM1186
REV. 1.2, JAN. 19, 2006
16
Macronix [ MACRONIX INTERNATIONAL ]
