Chopper-Stabilized Op Amps
ABSOLUTE MAXIMUM RATINGS
Total Supply Voltage (V+ to V-)..............................................18V
Input Voltage ........................................(V+ + 0.3V) to (V- - 0.3V)
Voltage on Oscillator Control Pins
(except EXT/CLOCK IN).............................................V+ to V-
Voltage on EXT/CLOCK IN..................(V+ + 0.3V) to (V+ - 6.0V)
Duration of Output Short Circuit ....................................Indefinite
Current into Any Pin ............................................................10mA
Current into Any Pin while Operating (Note 1)...................100µA
8-Pin TO-99 (derate 6.7mW/°C above +70°C)............533mW
14-Pin SO (derate 8.3mW/°C above +70°C)...............667mW
14-Pin PDIP (derate 10.0mW/°C above +70°C)..........800mW
14-Pin CERDIP (derate 9.1mW/°C above +70°C).......727mW
Operating Temperature Ranges
ICL765_C__/ICL755_BC__ ...............................0°C to +70°C
ICL765_I__/ICL755_BI__................................-20°C to +85°C
ICL765_M__/ICL755_BM__..........................-55°C to +125°C
Storage Temperature Range.............................-65°C to +150°C
Junction Temperature......................................................+150°C
Lead Temperature (soldering, 10s) .................................+300°C
Continuous Total Power Dissipation (T = +70°C)
A
8-Pin SO (derate 5.88mW/°C above +70°C)...............471mW
8-Pin PDIP (derate 6.9mW/°C above +70°C)...............552mW
8-Pin CERDIP (derate 8.0mW/°C above +70°C).........640mW
Note 1: Maxim recommends limiting the input current to 100µA to avoid latchup problems. A value of 1mA is typically safe; however,
this is not guaranteed.
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
ELECTRICAL CHARACTERISTICS—ICL7650B/ICL7653B
(Circuit of Figure 1, V+ = +5V, V- = -5V, T = +25°C, unless otherwise noted.)
A
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
0.7
10
MAX
UNITS
T
A
= +25°C
5
Input Offset Voltage
V
OS
-55°C < T < +85°C
µV
A
-55°C < T < +125°C
5.0
A
T
= +25°C
50
0.01
1.5
35
A
∆V
Average Temperature Coefficient
of Input Offset Voltage
OS
∆T
µV/°C
pA
-20°C < T < +85°C
A
0.05
10
T
= +25°C
A
Input Bias Current
I
Doubles every 10°
0°C < T < +70°C
A
BIAS
-20°C < T < +85°C
100
0.5
A
Input Offset Current (Note 2)
Input Resistance
I
T
A
= +25°C
pA
Ω
OS
12
R
IN
10
5
8
Large-Signal Voltage Gain
A
VOL
R = 10kΩ
L
V/V
1 · 10
5 · 10
R = 10kΩ
4.7
4.85
L
Output Voltage Swing (Note 3)
V
OUT
V
R = 100kΩ
L
4.95
Common-Mode Voltage Range
Common-Mode Rejection Ratio
Power-Supply Rejection Ratio
Input Noise Voltage
Input Noise Current
Unity-Gain Bandwidth
Slew Rate
CMVR
CMRR
PSRR
-5.0 -5.2 to +2.0 1.6
V
dB
CMVR = -5V to +1.6V
V+ to V- = 3V to 8V
120
120
130
130
2
dB
e
np-p
R = 100Ω, f = 0 to 10Hz
S
µVp-p
pA/√Hz
MHz
V/µs
µs
I
n
f = 10Hz
0.01
2.0
2.5
0.2
20
GBW
SR
C = 50pF, R = 10kΩ
L
L
Rise Time
t
r
Overshoot
%
Operating Supply Range
Supply Current
V+ to V-
4.5
16
V
I
No load
2.0
3.5
mA
SUPP
2
_______________________________________________________________________________________
MAXIM [ MAXIM INTEGRATED PRODUCTS ]
