MC33910G5AC/MC3433910G5AC
ELECTRICAL CHARACTERISTICS
STATIC ELECTRICAL CHARACTERISTICS
Table 4. Static Electrical Characteristics (continued)
Characteristics noted under conditions 5.5 V ≤ VSUP ≤ 18 V, -40°C ≤ TA ≤ 125°C for the 33910 and -40°C ≤ TA ≤ 85°C for the
34910, unless otherwise noted. Typical values noted reflect the approximate parameter mean at TA = 25°C under nominal
conditions, unless otherwise noted.
Characteristic
TXD INPUT PIN (LIN PHYSICAL LAYER) (TXD)
Low-state Input Voltage
Symbol
Min
Typ
Max
Unit
VIL
VIH
-0.3
0.7 x VDD
10
–
–
0.3 x VDD
VDD +0.3
30
V
V
High-state Input Voltage
Pin Pull-up Current, 0 V < VIN < 3.5 V
IPUIN
20
µA
LIN PHYSICAL LAYER WITH J2602 FEATURE ENABLED (BIT DIS_J2602 = 0)
LIN Under Voltage threshold
VTH_UNDER_
VOLTAGE
V
Positive and Negative threshold (VTHP, VTHN
)
5.0
6.0
Hysteresis (VTHP - VTHN
)
VJ2602_DEG
400
mV
LIN PHYSICAL LAYER, TRANSCEIVER (LIN)(37)
Operating Voltage Range
VBAT
VSUP
8.0
7.0
18
18
40
V
V
Supply Voltage Range
Voltage Range within which the device is not destroyed
VSUP_NON_OP
IBUS_LIM
-0.3
V
Current Limitation for Driver Dominant State
Driver ON, VBUS = 18 V
mA
40
-1.0
–
90
–
200
–
Input Leakage Current at the receiver
Driver off; VBUS = 0 V; VBAT = 12 V
IBUS_PAS_DOM
IBUS_PAS_REC
IBUS_NO_GND
mA
µA
Leakage Output Current to GND
Driver Off; 8.0 V < VBAT < 18 V; 8.0 V < VBUS < 18 V; VBUS ≥ VBAT
–
20
1.0
Control unit disconnected from ground(38)
mA
GNDDEVICE = VSUP; VBAT = 12 V; 0 < V
< 18 V
-1.0
–
BUS
V
Disconnected; VSUP_DEVICE = GND; 0 V < V
< 18 V(39)
BUS
IBUSNO_BAT
VBUSDOM
VBUSREC
µA
BAT
–
–
–
–
100
0.4
Receiver Dominant State
Receiver Recessive State
VSUP
VSUP
VSUP
0.6
0.475
–
–
Receiver Threshold Center
(VTH_DOM + VTH_REC)/2
VBUS_CNT
0.5
0.525
Receiver Threshold Hysteresis
VHYS
VSUP
(VTH_REC - VTH_DOM
)
–
–
0.175
Voltage Drop at the serial Diode in pull-up path
VSERDIODE
VSHIFT_BAT
VSHIFT_GND
0.4
0
1.0
V
VBAT_SHIFT
GND_SHIFT
Notes
11.5%
11.5%
VBAT
VBAT
0
37. Parameters guaranteed for 7.0 V ≤ VSUP ≤ 18 V.
38. Loss of local ground must not affect communication in the residual network.
39. Node has to sustain the current that can flow under this condition. Bus must remain operational under this condition.
33910
Analog Integrated Circuit Device Data
Freescale Semiconductor
14