欢迎访问ic37.com |
会员登录 免费注册
发布采购

EM636165-XXI 参数 Datasheet PDF下载

EM636165-XXI图片预览
型号: EM636165-XXI
PDF下载: 下载PDF文件 查看货源
内容描述: 1Mega ×16同步DRAM (SDRAM)的 [1Mega x 16 Synchronous DRAM (SDRAM)]
分类和应用: 动态存储器
文件页数/大小: 73 页 / 756 K
品牌: ETRON [ ETRON TECHNOLOGY, INC. ]
 浏览型号EM636165-XXI的Datasheet PDF文件第10页浏览型号EM636165-XXI的Datasheet PDF文件第11页浏览型号EM636165-XXI的Datasheet PDF文件第12页浏览型号EM636165-XXI的Datasheet PDF文件第13页浏览型号EM636165-XXI的Datasheet PDF文件第15页浏览型号EM636165-XXI的Datasheet PDF文件第16页浏览型号EM636165-XXI的Datasheet PDF文件第17页浏览型号EM636165-XXI的Datasheet PDF文件第18页  
EtronTech  
EM636165-XXI  
1M x 16 SDRAM  
Test Mode field (A8~A7)  
·
These two bits are used to enter the test mode and must be programmed to "00" in normal  
operation.  
A8  
0
A7  
0
Test Mode  
normal mode  
0
1
Vendor Use Only  
Vendor Use Only  
1
X
Single Write Mode (A9)  
·
This bit is used to select the write mode. When the BS bit is "0", the Burst-Read-Burst-  
Write mode is selected. When the BS bit is "1", the Burst-Read-Single-Write mode is  
selected.  
A9  
0
Single Write Mode  
Burst-Read-Burst-Write  
Burst-Read-Single-Write  
1
Note: A10 and A11 should stay Lduring mode set cycle.  
8
9
No-Operation command  
(RAS# = "H", CAS# = "H", WE# = "H")  
The No-Operation command is used to perform a NOP to the SDRAM which is selected (CS#  
is Low). This prevents unwanted commands from being registered during idle or wait states.  
Burst Stop command  
(RAS# = "H", CAS# = "H", WE# = "L")  
The Burst Stop command is used to terminate either fixed-length or full-page bursts. This  
command is only effective in a read/write burst without the auto precharge function. The terminated  
read burst ends after a delay equal to the CAS# latency (refer to the following figure). The  
termination of a write burst is shown in the following figure.  
T0  
T1  
T2  
T3  
T4  
T5  
T6  
T7  
T8  
CLK  
READ A  
NOP  
NOP  
NOP  
COMMAND  
NOP  
NOP  
Burst Stop  
DOUT A  
NOP  
NOP  
The burst ends after a delay equal to the CAS# latency.  
CAS# latency=1  
DOUT A  
DOUT A  
DOUT A  
0
1
2
3
t
, DQ's  
CK1  
CAS# latency=2  
, DQ's  
DOUT A  
DOUT A  
DOUT A  
2
DOUT A  
3
0
1
t
CK2  
CAS# latency=3  
, DQ's  
DOUT A  
0
DOUT A  
DOUT A  
DOUT A  
3
1
2
t
CK3  
Termination of a Burst Read Operation  
4, CAS# Latency = 1, 2, 3)  
(Burst Length  
Preliminary  
14  
Rev. 1.1 Apr. 2005  
 复制成功!