欢迎访问ic37.com |
会员登录 免费注册
发布采购

EN29LV641H-70TCP 参数 Datasheet PDF下载

EN29LV641H-70TCP图片预览
型号: EN29LV641H-70TCP
PDF下载: 下载PDF文件 查看货源
内容描述: 64兆位( 4096K ×16位)快闪记忆体, CMOS 3.0伏只统一部门快闪记忆体 [64 Megabit (4096K x 16-bit) Flash Memory, CMOS 3.0 Volt-only Uniform Sector Flash Memory]
分类和应用:
文件页数/大小: 46 页 / 523 K
品牌: EON [ EON SILICON SOLUTION INC. ]
 浏览型号EN29LV641H-70TCP的Datasheet PDF文件第8页浏览型号EN29LV641H-70TCP的Datasheet PDF文件第9页浏览型号EN29LV641H-70TCP的Datasheet PDF文件第10页浏览型号EN29LV641H-70TCP的Datasheet PDF文件第11页浏览型号EN29LV641H-70TCP的Datasheet PDF文件第13页浏览型号EN29LV641H-70TCP的Datasheet PDF文件第14页浏览型号EN29LV641H-70TCP的Datasheet PDF文件第15页浏览型号EN29LV641H-70TCP的Datasheet PDF文件第16页  
EN29LV641H/L EN29LV640U  
TABLE 4. Autoselect Codes (Using High Voltage, VID)  
A21  
to  
A14  
to  
A5  
A92 A8 A7 A6 to  
Description  
CE# OE# WE#  
A1 A0  
DQ15 to DQ0  
A15  
A10  
A2  
H1  
L
XX1Ch  
XX7Fh  
Manufacturer ID:  
Eon  
L
L
L
L
L
L
H
H
H
X
X
X
X
X
VID  
VID  
VID  
X
X
X
L
L
L
X
L
L
L
H
L
Autoselect  
Device ID  
X
X
X
X
22D7h  
XX01h  
(Protected)  
XX00h  
Sector Protection  
Verification  
SA  
H
(Unprotected)  
L=logic low= VIL, H=Logic High= VIH, VID =11 ± 0.5V, X=Don’t Care (either L or H, but not floating!), SA=Sector  
Addresses  
Note:  
1. A8=H is recommended for Manufacturing ID check. If a manufacturing ID is read with A8=L, the chip will output a  
configuration code 7Fh.  
2. A9 = VID is for HV A9 Autoselect mode only. A9 must be Vcc (CMOS logic level) for Command Autoselect  
Mode.  
ACC: Accelerated Program Operation  
The device offers accelerated program operation which enables the programming in higher speed.  
When ACC is raised to VHH, the memory automatically enters the Unlock Bypass mode (please refer to  
“Command Definitions”), temporarily unprotects every protected sector groups, and reduces the  
time required for program operation. The system would use a two-cycle program command sequence  
as required by the Unlock Bypass mode. When ACC returns to VIH or VIL, normal operation resumes.  
The transitions from VIH or VIL to VHH and from VHH to VIH or VIL must be slower than tVHH, see Figure 5.  
Note that the ACC pin must not be left floating or unconnected. In addition, ACC pin must not be at VHH  
for operations other than accelerated program. It could cause the device to be damaged. Never raise  
this pin to VHH from any mode except Read mode; otherwise the memory may be left in an  
indeterminate state.  
A 0.1µF capacitor should be connected between the ACC pin and the VSS Ground pin to decouple the  
current surges from the power supply. The PCB track widths must be sufficient to carry the currents  
required during Unlock Bypass Program.  
RESET#: Hardware Reset  
When RESET# is driven low for tRP, all output pins are tristates. All commands written in the internal  
state machine are reset to reading array data.  
Please refer to timing diagram for RESET# pin in “AC Characteristics”.  
Sector Group Protection & Unprotection  
The hardware sector group protection feature disables both program and erase operations in any sector  
group. The hardware chip unprotection feature re-enables both program and erase operations in previously  
This Data Sheet may be revised by subsequent versions  
or modifications due to changes in technical specifications.  
©2005 Eon Silicon Solution, Inc., www.essi.com.tw  
12  
Rev. B, Issue Date: 2005/06/27