AT90USB64/128
TA = -40°C to 85°C, VCC = 1.8V to 5.5V (unless otherwise noted) (Continued)
Symbol
Parameter
Condition
Min.(5)
Typ.
Max.(5)
Units
Active 1MHz, VCC = 2V
(AT90USB64/128)
0.8
mA
Active 4MHz, VCC = 3V
(AT90USB64/128)
5
18
mA
mA
mA
mA
mA
Active 8MHz, VCC = 5V
(AT90USB64/128)
Power Supply Current(6)
Idle 1MHz, VCC = 2V
(AT90USB64/128)
0.4
0.75
2.2
8
ICC
Idle 4MHz, VCC = 3V
(AT90USB64/128)
Idle 8MHz, VCC = 5V
(AT90USB64/128)
WDT enabled, VCC = 3V
WDT disabled, VCC = 3V
<10
<1
20
3
µA
µA
Power-down mode
VCC = 5V
Analog Comparator
Input Offset Voltage
VACIO
IACLK
tACID
<10
40
50
mV
nA
ns
Vin = VCC/2
Analog Comparator
Input Leakage Current
VCC = 5V
Vin = VCC/2
-50
Analog Comparator
Propagation Delay
VCC = 2.7V
VCC = 4.0V
750
500
Note:
1. "Max" means the highest value where the pin is guaranteed to be read as low
2. "Min" means the lowest value where the pin is guaranteed to be read as high
3. Although each I/O port can sink more than the test conditions (20mA at VCC = 5V, 10mA at VCC = 3V) under steady state
conditions (non-transient), the following must be observed:
AT90USB64/128:
1.)The sum of all IOL, for ports A0-A7, G2, C4-C7 should not exceed 100 mA.
2.)The sum of all IOL, for ports C0-C3, G0-G1, D0-D7 should not exceed 100 mA.
3.)The sum of all IOL, for ports G3-G5, B0-B7, E0-E7 should not exceed 100 mA.
4.)The sum of all IOL, for ports F0-F7 should not exceed 100 mA.
If IOL exceeds the test condition, VOL may exceed the related specification. Pins are not guaranteed to sink current greater
than the listed test condition.
4. Although each I/O port can source more than the test conditions (20mA at VCC = 5V, 10mA at VCC = 3V) under steady
state conditions (non-transient), the following must be observed:
AT90USB64/128:
1)The sum of all IOH, for ports A0-A7, G2, C4-C7 should not exceed 100 mA.
2)The sum of all IOH, for ports C0-C3, G0-G1, D0-D7 should not exceed 100 mA.
3)The sum of all IOH, for ports G3-G5, B0-B7, E0-E7 should not exceed 100 mA.
4)The sum of all IOH, for ports F0-F7 should not exceed 100 mA.
5. All DC Characteristics contained in this datasheet are based on simulation and characterization of other AVR microcontrol-
lers manufactured in the same process technology. These values are preliminary values representing design targets, and
will be updated after characterization of actual silicon
6. Values with “Power Reduction Register 1 - PRR1” disabled (0x00).
401
7593A–AVR–02/06
ATMEL [ ATMEL ]
