欢迎访问ic37.com |
会员登录 免费注册
发布采购

EPM9560A 参数 Datasheet PDF下载

EPM9560A图片预览
型号: EPM9560A
PDF下载: 下载PDF文件 查看货源
内容描述: 可编程逻辑器件系列 [Programmable Logic Device Family]
分类和应用: 可编程逻辑器件
文件页数/大小: 46 页 / 495 K
品牌: ALTERA [ ALTERA CORPORATION ]
 浏览型号EPM9560A的Datasheet PDF文件第25页浏览型号EPM9560A的Datasheet PDF文件第26页浏览型号EPM9560A的Datasheet PDF文件第27页浏览型号EPM9560A的Datasheet PDF文件第28页浏览型号EPM9560A的Datasheet PDF文件第30页浏览型号EPM9560A的Datasheet PDF文件第31页浏览型号EPM9560A的Datasheet PDF文件第32页浏览型号EPM9560A的Datasheet PDF文件第33页  
MAX 9000 Programmable Logic Device Family Data Sheet  
Table 20. MAX 9000A Device Typical ICC Supply Current Values  
Symbol  
Parameter  
Conditions  
EPM9320A EPM9560A Unit  
ICC1  
ICC supply current (low-power mode, VI = ground, no load (11)  
99  
174  
mA  
standby, typical)  
Notes to tables:  
(1) See the Operating Requirements for Altera Devices Data Sheet.  
(2) Minimum DC input on I/ O pins is –0.5 V and on the four dedicated input pins is –0.3 V. During transitions, the  
inputs may undershoot to –2.0 V or overshoot to 7.0 V for periods shorter than 20 ns under no-load conditions.  
(3)  
(4) Numbers in parentheses are for industrial-temperature-range devices.  
(5) Typical values are for T = 25° C and V = 5.0 V.  
V
must rise monotonically.  
CC  
A
CC  
(6) These values are specified under the MAX 9000 recommended operating conditions, shown in Table 15 on page 27.  
(7) During in-system programming, the minimum V of the JTAG TCKpin is 3.6 V. The minimum V of this pin  
IH  
IH  
during JTAG testing remains at 2.0 V. To attain this 3.6-V V during programming, the ByteBlaster and  
IH  
ByteBlasterMV download cables must have a 5.0-V V  
.
CC  
(8) This parameter is measured with 50% of the outputs each sinking 12 mA. The I  
parameter refers to high-level  
OH  
TTL or CMOS output current; the I parameter refers to the low-level TTL or CMOS output current.  
OL  
(9) JTAG pin input leakage is typically –60 µΑ.  
(10) Capacitance is sample-tested only and is measured at 25° C.  
(11) Measured with a 16-bit loadable, enabled, up/ down counter programmed into each LAB. I is measured at 0° C.  
CC  
Figure 13 shows typical output drive characteristics for MAX 9000 devices  
with 5.0-V and 3.3-V VCCIO  
.
Figure 13. Output Drive Characteristics of MAX 9000 Devices  
Note (1)  
5.0-V  
3.3-V  
150  
120  
90  
150  
120  
90  
IOL  
IOL  
Typical I  
VCCIO = 3.3 V  
Room Temperature  
VCCIO = 5.0 V  
Room Temperature  
Typical I  
Output  
Current (mA)  
O
O
Output  
Current (mA)  
60  
30  
60  
30  
IOH  
IOH  
3.3  
1
2
3
4
5
1
2
3
4
5
Output Voltage (V)  
Output Voltage (V)  
Note:  
(1) Output drive characteristics include the JTAG TDOpin.  
Altera Corporation  
29  
 复制成功!