欢迎访问ic37.com |
会员登录 免费注册
发布采购

AD5382BST-5 参数 Datasheet PDF下载

AD5382BST-5图片预览
型号: AD5382BST-5
PDF下载: 下载PDF文件 查看货源
内容描述: 32通道, 3 V / 5 V单电源, 14位电压输出DAC [32-Channel, 3 V/5 V, Single-Supply, 14-Bit, Voltage Output DAC]
分类和应用: 转换器数模转换器
文件页数/大小: 40 页 / 616 K
品牌: ADI [ ADI ]
 浏览型号AD5382BST-5的Datasheet PDF文件第28页浏览型号AD5382BST-5的Datasheet PDF文件第29页浏览型号AD5382BST-5的Datasheet PDF文件第30页浏览型号AD5382BST-5的Datasheet PDF文件第31页浏览型号AD5382BST-5的Datasheet PDF文件第33页浏览型号AD5382BST-5的Datasheet PDF文件第34页浏览型号AD5382BST-5的Datasheet PDF文件第35页浏览型号AD5382BST-5的Datasheet PDF文件第36页  
AD5382  
DV  
DD  
8XC51  
AD5382 to PIC16C6x/7x  
AD5382  
SER/PAR  
The PIC16C6x/7x synchronous serial port (SSP) is configured  
as an SPI master with the Clock Polarity bit = 0. This is done by  
writing to the synchronous serial port control register  
RESET  
RxD  
SDO  
DIN  
(SSPCON). See the PIC16/17 Microcontroller User Manual. In  
TxD  
P1.1  
SCLK  
SYNC  
SPI/I2C  
this example I/O, port RA1 is being used to pulse  
and  
SYNC  
enable the serial port of the AD5382. This microcontroller  
transfers only eight bits of data during each serial transfer  
operation; therefore, three consecutive read/write operations  
may be needed depending on the mode. Figure 36 shows the  
connection diagram.  
Figure 37. AD5382-to-8051 Interface  
AD5382 to ADSP-2101/ADSP-2103  
Figure 38 shows a serial interface between the AD5382 and the  
ADSP-2101/ADSP-2103. The ADSP-2101/ADSP-2103 should  
be set up to operate in SPORT transmit alternate framing mode.  
The ADSP-2101/ADSP-2103 SPORT is programmed through  
the SPORT control register and should be configured as follows:  
internal clock operation, active low framing, and 16-bit word  
length. Transmission is initiated by writing a word to the Tx  
register after the SPORT has been enabled.  
DV  
DD  
PIC16C6X/7X  
AD5382  
SER/PAR  
RESET  
SDO  
SDI/RC4  
SDO/RC5  
SCK/RC3  
RA1  
DIN  
SCLK  
SYNC  
SPI/I2C  
Figure 36. AD5382-to-PIC16C6x/7x Interface  
DV  
DD  
ADSP-2101/  
ADSP-2103  
AD5382  
SER/PAR  
AD5382 to 8051  
RESET  
SDO  
The AD5382 requires a clock synchronized to the serial data.  
The 8051 serial interface must therefore be operated in Mode 0.  
In this mode, serial data enters and exits through RxD, and a  
shift clock is output on TxD. Figure 37 shows how the 8051 is  
connected to the AD5382. Because the AD5382 shifts data out  
on the rising edge of the shift clock and latches data in on the  
falling edge, the shift clock must be inverted. The AD5382  
requires its data to be MSB first. Since the 8051 outputs the LSB  
first, the transmit routine must take this into account.  
DR  
DT  
SCK  
TFS  
RFS  
DIN  
SCLK  
SYNC  
SPI/I2C  
Figure 38. AD5382-to-ADSP-2101/ADSP-2103 Interface  
Rev. 0 | Page 32 of 40