Spartan-3E FPGA Family: Introduction and Ordering Information
Revision History
The following table shows the revision history for this document.
Date
Version
1.0
Revision
03/01/2005
03/21/2005
Initial Xilinx release.
1.1
Added XC3S250E in CP132 package to Table 2. Corrected number of differential I/O pairs for CP132
package. Added package markings for QFP packages (Figure 2) and CP132/CPG132 packages
(Figure 4).
11/23/2005
03/22/2006
2.0
3.0
Added differential HSTL and SSTL I/O standards. Updated Table 2 to indicate number of input-only
pins. Added Production Stepping information, including example top marking diagrams.
Upgraded data sheet status to Preliminary. Added XC3S100E in CP132 package and updated I/O
counts for the XC3S1600E in FG320 package (Table 2). Added information about dual markings for –
5C and –4I product combinations to Package Marking.
11/09/2006
3.4
Added 66 MHz PCI support and links to the Xilinx PCI LogiCORE data sheet. Indicated that Stepping
1 parts are Production status. Promoted Module 1 to Production status. Synchronized all modules to
v3.4.
04/18/2008
08/26/2009
3.7
3.8
Added XC3S500E VQG100 package. Added reference to XA Automotive version. Updated links.
Added paragraph to Configuration indicating the device supports MultiBoot configuration. Added
package sizes to Table 2. Described the speed grade and temperature range guarantee for devices
having a single mark in paragraph 3 under Package Marking. Deleted Pb-Free Packaging example
under Ordering Information. Revised information under Production Stepping. Revised description of
Table 3.
10/29/2012
4.0
Added Notice of Disclaimer. This product is not recommended for new designs.
Updated Table 2 footprint size of PQ208.
07/19/2013
12/14/2018
4.1
4.2
Removed banner. This product IS recommended for new designs.
Updated for Lead-Frame Plating Composition Change For Legacy Eutectic Products (XCN18024).
Notice of Disclaimer
THE XILINX HARDWARE FPGA AND CPLD DEVICES REFERRED TO HEREIN (“PRODUCTS”) ARE SUBJECT TO THE TERMS AND
CONDITIONS OF THE XILINX LIMITED WARRANTY WHICH CAN BE VIEWED AT http://www.xilinx.com/warranty.htm. THIS LIMITED
WARRANTY DOES NOT EXTEND TO ANY USE OF PRODUCTS IN AN APPLICATION OR ENVIRONMENT THAT IS NOT WITHIN THE
SPECIFICATIONS STATED IN THE XILINX DATA SHEET. ALL SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.
PRODUCTS ARE NOT DESIGNED OR INTENDED TO BE FAIL-SAFE OR FOR USE IN ANY APPLICATION REQUIRING FAIL-SAFE
PERFORMANCE, SUCH AS LIFE-SUPPORT OR SAFETY DEVICES OR SYSTEMS, OR ANY OTHER APPLICATION THAT INVOKES
THE POTENTIAL RISKS OF DEATH, PERSONAL INJURY, OR PROPERTY OR ENVIRONMENTAL DAMAGE (“CRITICAL
APPLICATIONS”). USE OF PRODUCTS IN CRITICAL APPLICATIONS IS AT THE SOLE RISK OF CUSTOMER, SUBJECT TO
APPLICABLE LAWS AND REGULATIONS.
CRITICAL APPLICATIONS DISCLAIMER
XILINX PRODUCTS (INCLUDING HARDWARE, SOFTWARE AND/OR IP CORES) ARE NOT DESIGNED OR INTENDED TO BE
FAIL-SAFE, OR FOR USE IN ANY APPLICATION REQUIRING FAIL-SAFE PERFORMANCE, SUCH AS IN LIFE-SUPPORT OR
SAFETY DEVICES OR SYSTEMS, CLASS III MEDICAL DEVICES, NUCLEAR FACILITIES, APPLICATIONS RELATED TO THE
DEPLOYMENT OF AIRBAGS, OR ANY OTHER APPLICATIONS THAT COULD LEAD TO DEATH, PERSONAL INJURY OR SEVERE
PROPERTY OR ENVIRONMENTAL DAMAGE (INDIVIDUALLY AND COLLECTIVELY, “CRITICAL APPLICATIONS”). FURTHERMORE,
XILINX PRODUCTS ARE NOT DESIGNED OR INTENDED FOR USE IN ANY APPLICATIONS THAT AFFECT CONTROL OF A
VEHICLE OR AIRCRAFT, UNLESS THERE IS A FAIL-SAFE OR REDUNDANCY FEATURE (WHICH DOES NOT INCLUDE USE OF
SOFTWARE IN THE XILINX DEVICE TO IMPLEMENT THE REDUNDANCY) AND A WARNING SIGNAL UPON FAILURE TO THE
OPERATOR. CUSTOMER AGREES, PRIOR TO USING OR DISTRIBUTING ANY SYSTEMS THAT INCORPORATE XILINX
PRODUCTS, TO THOROUGHLY TEST THE SAME FOR SAFETY PURPOSES. TO THE MAXIMUM EXTENT PERMITTED BY
APPLICABLE LAW, CUSTOMER ASSUMES THE SOLE RISK AND LIABILITY OF ANY USE OF XILINX PRODUCTS IN CRITICAL
APPLICATIONS.
DS312 (v4.2) December 14, 2018
www.xilinx.com
Product Specification
7
XILINX [ XILINX, INC ]
