欢迎访问ic37.com |
会员登录 免费注册
发布采购

WM8746SEDS 参数 Datasheet PDF下载

WM8746SEDS图片预览
型号: WM8746SEDS
PDF下载: 下载PDF文件 查看货源
内容描述: 24位, 192kHz的6通道DAC,具有音量控制 [24-bit, 192kHz 6-Channel DAC with Volume Control]
分类和应用:
文件页数/大小: 32 页 / 387 K
品牌: WOLFSON [ WOLFSON MICROELECTRONICS PLC ]
 浏览型号WM8746SEDS的Datasheet PDF文件第17页浏览型号WM8746SEDS的Datasheet PDF文件第18页浏览型号WM8746SEDS的Datasheet PDF文件第19页浏览型号WM8746SEDS的Datasheet PDF文件第20页浏览型号WM8746SEDS的Datasheet PDF文件第22页浏览型号WM8746SEDS的Datasheet PDF文件第23页浏览型号WM8746SEDS的Datasheet PDF文件第24页浏览型号WM8746SEDS的Datasheet PDF文件第25页  
WM8746  
Production Data  
HARDWARE CONTROL MODES  
When the MODE pin is held high the following hardware modes of operation are available.  
MUTE AND AUTOMUTE OPERATION  
Pin 9 (MUTE) controls selection of MUTE directly, and can be used to enable and disable the  
automute function, or as an output of the automuted signal.  
AUTOMUTED (Internal  
Signal)  
10k  
SOFTMUTE  
(Internal  
Signal)  
MUTE  
PIN  
Figure 12 Mute Circuit Operation  
The MUTE pin behaves as a bi-directional function, that is, as an input to select MUTE or NOT-  
MUTE, or as an output indication of automute operation. MUTE is active high; taking the pin high  
causes the filters to soft mute, ramping down the audio signal over a few milliseconds. Taking MUTE  
low again allows data into the filter.  
The automute function detects a series of zero value audio samples of 1024 samples long being  
applied to all 6 channels. After such an event, a latch is set whose output (AUTOMUTED) is wire  
OR’ed through a 10kohm resistor to the MUTE pin. Thus if the MUTE pin is not being driven, the  
automute function will assert MUTE.  
If MUTE is tied low, AUTOMUTED is overridden and will not mute. If MUTE is driven from a source  
follower, or diode, then both MUTE and automute functions are available. If MUTE is not driven,  
AUTOMUTED appears as a weak output (10k source impedance) so can be used to drive external  
mute circuits.  
ML/I2S AND MC/IWL INPUT FORMAT SELECTION  
In hardware mode, pins 12 and 13 become input controls for selection of input data format type and  
input data word length, see Table 5. I2S mode is designed to support any word length provided  
enough bit clocks are sent.  
ML/I2S  
MC/IWL  
INPUT DATA MODE  
16-bit right justified  
20-bit right justified  
24-bit right justified  
I2S mode  
0
0
1
1
0
1
0
1
Table 9 Control of Input Data Format Type and Input Data Word Length  
MD/DM DE-EMPHASIS  
In hardware mode, pin 14 becomes an input control for selection of de-emphasis filtering to be  
applied. See Table 5.  
MD/DM  
DE-EMPHASIS MODE  
De-emphasis off  
0
1
De-emphasis on  
Table 10 De-emphasis Control  
March 2006, PD Rev 4.0  
21  
w
 复制成功!