78P2343JAT
3-port E3/DS3/STS-1 LIU
with Jitter Attenuator
On the transmit side, when the ENDEC is enabled,
NRZ input data is encoded to Positive and Negative
AMI logic data following the B3ZS (for DS3/STS-1)
or HDB3 (for E3) substitution codes. The NRZ data
is input to the TPOS pin as shown below:
B3ZS/HDB3 ENDEC WITH LINE CODE VIOLATION
DETECT
The 78P2343JAT includes a selectable B3ZS/HDB3
Encoder/Decoder (ENDEC). The ENDEC function
can be enabled or disabled through pin selection or
register setting as shown below.
ENDECB
TPOSx
TNEGx
bit/pin
0 / L
ENDECB
RPOSx
RNEGx
bit/pin
NRZ data
‘Don’t Care’
1 / H
Positive AMI
Negative AMI
Receive Line Code
Violation Indicator
0 / L
NRZ data
TRANSMITTER OPERATION
1 / H
Positive AMI
Negative AMI
Transmitters 1-3 are enabled by their corresponding
TXEN bit. When enabled, each transmitter accepts
logic level clock and data signals and generates
current pulses on the LOUTPx and LOUTNx pins.
When properly connected to a 1:2CT center-tapped
transformer, a standards compliant AMI pulse is
When the ENDEC is enabled, the decoder
generates a composite NRZ logic data stream
following the B3ZS (for DS3/STS-1) or HDB3 (for E3)
substitution codes via the RPOSx pins:
generated which can drive a 75
Ω coaxial cable.
The decoder also detects Receive Line Code
Violations (RLCV) and outputs a pulse via the
RNEG pin. Three different classes of line code
violations are detected.
When the recommended transformer is used and
when DS3 mode is selected, the transmitted pulse
shape at the end of the 75
Ω terminated cable of 0 to
450 feet will fit the DS3 template in ANSI T1.102-
1993 and Telcordia GR-499-CORE. For STS-1
applications, the transmitted pulse for a short cable
meets the requirements of Telcordia GR-253-CORE.
For E3 applications, the transmitted pulse for a short
cable meets the requirements of ITU-T G.703.
1) Too many zeros:
More than two (three)
consecutive zeros in B3ZS (HDB3) mode.
2) Not enough zeros between bipolar pulse (B)
and bipolar violation pulse (V): (B,V) for B3ZS.
(B,V) or (B,0,V) for HDB3.
3) Code violation: Even number of bipolar pulses
(B) detected between bipolar violation pulses
(V).
In either DS3 and STS-1 modes, the LBOx pin or
LBO bit should be set high for short cable (< 225 ft),
and should be set low for long cable (> 225 ft). The
LBO settings are ignored in E3 mode.
When the ENDEC is disabled, the 78P2343JAT
outputs a dual rail data stream via the RPOSx and
RNEGx pins. In this mode, the Framer/Mapper
providing the ENDEC function typically detects Line
Code Violations.
RCLK/TCLK POLARITY REVERSAL
To simplify the interface with various framer circuitry,
TCLK polarity can be internally inverted by setting
the TCLKP bit, and RCLK polarity can be inverted
by setting the RCLKP bit. Both bits are located in
the Master Control Register (MSCR).
REMOTE (DIGITAL) LOOPBACK
When the Register Control bit, REGEN, is disabled
and the LPBKx pin is floating; or when the Register
Control bit, REGEN, is enabled and the RLBK bit is
set, RCLKx, RNEGx, and RPOSx outputs are
internally looped back to the TCLKx, TNEGx, and
TPOSx inputs respectively.
Page 4 of 37
2005 Teridian Semiconductor Corporation
Rev 2.2
TERIDIAN [ TERIDIAN SEMICONDUCTOR CORPORATION ]
