欢迎访问ic37.com |
会员登录 免费注册
发布采购

71M6511H-IGTR 参数 Datasheet PDF下载

71M6511H-IGTR图片预览
型号: 71M6511H-IGTR
PDF下载: 下载PDF文件 查看货源
内容描述: 单相电能计量芯片 [Single-Phase Energy Meter IC]
分类和应用:
文件页数/大小: 95 页 / 860 K
品牌: TERIDIAN [ TERIDIAN SEMICONDUCTOR CORPORATION ]
 浏览型号71M6511H-IGTR的Datasheet PDF文件第36页浏览型号71M6511H-IGTR的Datasheet PDF文件第37页浏览型号71M6511H-IGTR的Datasheet PDF文件第38页浏览型号71M6511H-IGTR的Datasheet PDF文件第39页浏览型号71M6511H-IGTR的Datasheet PDF文件第41页浏览型号71M6511H-IGTR的Datasheet PDF文件第42页浏览型号71M6511H-IGTR的Datasheet PDF文件第43页浏览型号71M6511H-IGTR的Datasheet PDF文件第44页  
71M6511/71M6511H  
Single-Phase Energy Meter IC  
DATA SHEET  
AUGUST 2007  
Dedicated Segment Pins  
Shared w/ DIO4-DIO11  
Shared w/ DIO14-DIO17  
SEG0  
P0  
SEG1  
P4  
SEG19 SEG24  
SEG31 SEG34  
...  
SEG37  
P124  
P125  
P126  
P127  
COM0  
COM1  
COM2  
COM3  
P76  
P77  
P78  
P79  
P80  
P81  
P82  
P83  
P108  
P109  
P110  
P111  
P112  
P113  
P114  
P115  
P1  
P5  
P2  
P6  
P3  
P7  
Table 56: Liquid Crystal Display Segment Table (Typical)  
Note: P0, P1, … Represent the pixel/segment numbers on the LCD.  
A charge pump suitable for driving VLCD is included on-chip. This circuit creates 5V from the 3.3V supply. A contrast DAC is  
provided that permits the LCD full-scale voltage to be adjusted between VLCD and 70% of VLCD. The LCD_NUM register  
defines the number of dual purpose pins used for LCD segment interface.  
LCD Voltage Boost Circuitry  
A voltage boost circuit may be used to generate 5V from the 3.3V supply to support low-power 5V devices, such as LCDs.  
Figure 10 shows a block diagram of the voltage boost circuitry including the voltage regulators for V2P5 and V2P5NV. When  
activated using the I/O RAM register LCD_BSTEN (0x2020[7]), the boost circuitry provides an AC voltage at the VDRV output  
pin (see the Applications section for details).  
VOLTAGE  
BOOST  
VDRV  
LCD_IBST  
LCD_BSTEN  
GNDD  
GNDD  
V2P5NV  
V3P3D  
VOLT  
REG  
V3P3D  
VBAT  
GNDD  
GNDD  
V2P5  
0.1V  
V2P5  
VLCD  
Figure 10: LCD Voltage Boost Circuitry  
UART (UART0) and Optical Port (UART1)  
The 71M6511/6511H includes an interface to implement an IR or optical port. The pin OPT_TX is designed to directly drive an  
external LED for transmitting data on an optical link (low-active). The pin OPT_RX, also low-active, is designed to sense the  
input from an external photo detector used as the receiver for the optical link. These two pins are connected to a dedicated  
UART port. OPT_TX can be tristated if it is desired to multiplex another I/O pin to the OPT_TX output. The control bit for the  
OPT_TX output is the I/O RAM register OPT_TXDIS (0x2008[5]).  
Page: 40 of 95  
© 2005-2007 TERIDIAN Semiconductor Corporation  
V2.6  
 复制成功!