欢迎访问ic37.com |
会员登录 免费注册
发布采购

SP37E760 参数 Datasheet PDF下载

SP37E760图片预览
型号: SP37E760
PDF下载: 下载PDF文件 查看货源
内容描述: 3.3 V的I / O控制器的嵌入式应用 [3.3 V I/O CONTROLLER FOR EMBEDDED APPLICATIONS]
分类和应用: 控制器
文件页数/大小: 78 页 / 507 K
品牌: SMSC [ SMSC CORPORATION ]
 浏览型号SP37E760的Datasheet PDF文件第7页浏览型号SP37E760的Datasheet PDF文件第8页浏览型号SP37E760的Datasheet PDF文件第9页浏览型号SP37E760的Datasheet PDF文件第10页浏览型号SP37E760的Datasheet PDF文件第12页浏览型号SP37E760的Datasheet PDF文件第13页浏览型号SP37E760的Datasheet PDF文件第14页浏览型号SP37E760的Datasheet PDF文件第15页  
PIN #  
BUFFER  
TYPE  
I/OD12  
NAME  
SYMBOL  
DESCRIPTION  
TQFP  
57  
QFP  
59  
SLCT  
This high active output from the printer indicates that  
it has power on. Bit 4 of the Printer Status Register  
Printer  
Selected  
Status  
reads the SLCT input.  
Refer to Parallel Port  
description for use of this pin in ECP and EPP mode.  
nERROR  
PD0-4  
A low on this input from the printer indicates that there  
is a error condition at the printer. Bit 3 of the Printer  
Status register reads the nERR input. Refer to  
Parallel Port description for use of this pin in ECP and  
EPP mode.  
73  
75  
nError  
I/OD12  
Port Data 0-4  
69-66, 64 71-68, 66 Port Data 0-  
Port Data 4  
IOP14/IS  
IOP14  
63  
62  
65  
64  
Port Data 5  
Port Data 6  
PD5  
PD6  
Port Data 5  
Port Data 6  
IOP14/  
OD12  
61  
63  
Port Data 7  
PD7  
IOP14  
MISC  
ICLK  
Port Data 7  
18  
92  
20  
94  
14.318 MHz  
Input Clock  
CLK14  
nADRX  
The external connection to a single source 14.318  
MHz clock.  
Active low address decode out: used to decode a 1,  
8, or 16 byte address block. (An external pull-up is  
required). Refer to Configuration registers CR03,  
CR08 and CR09 for more information.  
The interrupt request from a logical device or IRQIN  
may be output on IRQ_B. Refer to the configuration  
registers for more information. If EPP or ECP Mode  
is enabled, this output is pulsed low and released to  
allow sharing of interrupts.  
Address X/  
O12/ OD12  
Interrupt  
Request B  
IRQ_B  
PWRGD  
This active high input indicates that the power (VCC)  
is valid. For device operation PWRGD must be  
active. When PWRGD is inactive, all inputs are  
disconnected and put into a low power mode; all  
outputs are put into high impedance. The contents af  
all registers are preserved as long as VCC is valid.  
The output driver current drain when PWRGD is  
inactive mode drops to ISTBY - standby current.  
56  
58  
Power Good  
I/O4  
96  
98  
External  
IRQIN  
IS  
This pin is used to steer an interrupt signal from an  
Interrupt Input  
external device onto one of eight IRQ outputs IRQA-  
H.  
POWER INTERFACE  
Positive Supply Voltage.  
13,70  
15,72  
Power  
Ground  
VCC  
VSS  
4, 10, 11, 6, 12, 13,  
Ground Supply.  
12, 14, 15, 14, 16, 17,  
23, 45,  
65, 93  
25, 47,  
67, 95  
1, 2, 3, 5, 1, 2, 3, 4,  
6, 7, 8, 9, 5, 7, 8, 9,  
16, 21, 24, 10, 11, 18,  
Non Connect NC  
Non-Connected Pins  
99, 100  
23, 26,  
SMSC DS – SP37E760  
Page 11  
Rev. 04/13/2001  
 复制成功!