欢迎访问ic37.com |
会员登录 免费注册
发布采购

COM200221 参数 Datasheet PDF下载

COM200221图片预览
型号: COM200221
PDF下载: 下载PDF文件 查看货源
内容描述: 10 Mbps的ARCNET ( ANSI 878.1 )控制器2Kx8片上RAM [10 Mbps ARCNET (ANSI 878.1) Controller with 2Kx8 On-Chip RAM]
分类和应用: 控制器
文件页数/大小: 82 页 / 509 K
品牌: SMSC [ SMSC CORPORATION ]
 浏览型号COM200221的Datasheet PDF文件第21页浏览型号COM200221的Datasheet PDF文件第22页浏览型号COM200221的Datasheet PDF文件第23页浏览型号COM200221的Datasheet PDF文件第24页浏览型号COM200221的Datasheet PDF文件第26页浏览型号COM200221的Datasheet PDF文件第27页浏览型号COM200221的Datasheet PDF文件第28页浏览型号COM200221的Datasheet PDF文件第29页  
10 Mbps ARCNET (ANSI 878.1) Controller with 2Kx8 On-Chip RAM  
Datasheet  
VALID  
A2-A0, nCS  
nRD  
Delayed nRD  
(nRD1)  
Sampled A2-A0, nCS  
VALID  
More delayed nRD  
(nRD2)  
Figure 5.7 - High Speed CPU Bus Timing - Intel CPU Mode  
The I/O address and Chip Select signals, which are supplied to the data output logic, are not sampled.  
Also, the nRD signal is not delayed, because the above sampling and delaying paths decrease the data  
access time of the read cycle.  
The above sampling and delaying signals are supplied to the Read Pulse Generation logic which  
generates the clearing pulse for the Diagnostic register and generates the starting pulse of the RAM  
Arbitration. Typical delay time between nRD and nRD1 is around 15nS and between nRD1 and nRD2 is  
around 10nS.  
Longer pulse widths are needed due to these delays on nRD signal. However, the CPU can insert some  
wait cycles to extend the width without any impact on performance.  
The BUSTMG pin is used to support this function. It is used to Enable/Disable the High Speed CPU Read  
and Write function. It is defined as: BUSTMG = 0, the High Speed CPU Read and Write operations are  
enabled; BUSTMG = 1, the High Speed CPU Read and Write operations are disabled if the RBUSTMG bit  
is 0. If BUSTMG = 1 and RBUSTMG = 1, High Speed CPU Read operations are enabled (see definition of  
RBUSTMG bit below).  
The RBUSTMG bit was added to Disable/Enable the High Speed CPU Read function. It is defined as:  
RBUSTMG=0, Disabled (Default); RBUSTMG=1, Enabled.  
In the MOTOROLA CPU mode (DIR, nDS mode), the same modifications apply.  
BUSTMG PIN  
RBUSTMG BIT  
BUS TIMING MODE  
High Speed CPU Read and Write  
0
1
1
X
0
1
Normal Speed CPU Read and Write  
High Speed CPU Read and Normal Speed CPU Write  
5.2  
Transmission Media Interface  
The bottom halves of Figure 5.1 and Figure 5.2 illustrate the COM20022I interface to the transmission  
media used to connect the node to the network. Table 5.1 lists different types of cable which are suitable  
for ARCNET applications. The user may interface to the cable of choice in one of three ways:  
SMSC COM20022I  
Page 25  
Revision 09-27-07  
DATASHEET  
 复制成功!