STK415-100-E
STK415-100 Series BTL Application
STK415-100 series
(*1) The voltage applied to the Stand-by pin (#17) must not
exceed the maximum rated value (VST max).
+OFF
SET SET
OUT OUT OUT OUT
IN NF ST- NF IN
Ch1Ch1 BY Ch2 Ch2
+Pre
GND
+V
1
-OFF -Pre
+V
L
H
-V
-V
6
L
Ch1+ Ch1- Ch2+ Ch2-
SUB
H
2
3
4
7
8
9
10 11 12 13 14 15 16 17 18 19
5
R30 (*1)
100
pF
Stand-By Control
Voltage VST
56kΩ
56kΩ
60V 60V
/3A /3A
3pF
560Ω 560Ω
3pF
22μF
/10V
22μF
/10V
GND
100Ω/
1W
1kΩ
+V
H
Ch1 IN
100μF
/100V
2.2μF
15V
56kΩ
100μF
/50V
+V
L
/100V
33μF
33μF
100μF
/50V
3μH
Ch2 OUT
GND
0.1μF
4.7Ω
100μF
/50V
100μF
/100V
4.7Ω/1W
-V
L
R
=8Ω
GND
15V
L
100μF
/100V
100Ω/
1W
3μH
0.1μF
4.7Ω/1W
-V
H
4.7Ω
Ch1 OUT
SANYO Semiconductor Co.,Ltd. assumes no responsibility for equipment failures that result from using
products at values that exceed, even momentarily, rated values (such as maximum ratings, operating condition
ranges, or other parameters) listed in products specifications of any and all SANYO Semiconductor Co.,Ltd.
products described or contained herein.
SANYO Semiconductor Co.,Ltd. strives to supply high-quality high-reliability products, however, any and all
semiconductor products fail or malfunction with some probability. It is possible that these probabilistic failures or
malfunction could give rise to accidents or events that could endanger human lives, trouble that could give rise
to smoke or fire, or accidents that could cause damage to other property. When designing equipment, adopt
safety measures so that these kinds of accidents or events cannot occur. Such measures include but are not
limited to protective circuits and error prevention circuits for safe design, redundant design, and structural
design.
In the event that any or all SANYO Semiconductor Co.,Ltd. products described or contained herein are
controlled under any of applicable local export control laws and regulations, such products may require the
export license from the authorities concerned in accordance with the above law.
No part of this publication may be reproduced or transmitted in any form or by any means, electronic or
mechanical, including photocopying and recording, or any information storage or retrieval system, or otherwise,
without the prior written consent of SANYO Semiconductor Co.,Ltd.
Any and all information described or contained herein are subject to change without notice due to
product/technology improvement, etc. When designing equipment, refer to the "Delivery Specification" for the
SANYO Semiconductor Co.,Ltd. product that you intend to use.
Information (including circuit diagrams and circuit parameters) herein is for example only; it is not guaranteed
for volume production.
Upon using the technical information or products described herein, neither warranty nor license shall be granted
with regard to intellectual property rights or any other rights of SANYO Semiconductor Co.,Ltd. or any third
party. SANYO Semiconductor Co.,Ltd. shall not be liable for any claim or suits with regard to a third party's
intellectual property rights which has resulted from the use of the technical information and products mentioned
above.
This catalog provides information as of July 2009. Specifications and information herein are subject
to change without notice.
No. A1469-12/12
PS
SANYO [ SANYO SEMICON DEVICE ]
