欢迎访问ic37.com |
会员登录 免费注册
发布采购

FM21L16-60-TGTR 参数 Datasheet PDF下载

FM21L16-60-TGTR图片预览
型号: FM21L16-60-TGTR
PDF下载: 下载PDF文件 查看货源
内容描述: [Memory Circuit, 128KX16, CMOS, PDSO44, 0.400 INCH, GREEN, MS-024GAC, TSOP2-44]
分类和应用: 存储
文件页数/大小: 14 页 / 225 K
品牌: RAMTRON [ RAMTRON INTERNATIONAL CORPORATION ]
 浏览型号FM21L16-60-TGTR的Datasheet PDF文件第3页浏览型号FM21L16-60-TGTR的Datasheet PDF文件第4页浏览型号FM21L16-60-TGTR的Datasheet PDF文件第5页浏览型号FM21L16-60-TGTR的Datasheet PDF文件第6页浏览型号FM21L16-60-TGTR的Datasheet PDF文件第8页浏览型号FM21L16-60-TGTR的Datasheet PDF文件第9页浏览型号FM21L16-60-TGTR的Datasheet PDF文件第10页浏览型号FM21L16-60-TGTR的Datasheet PDF文件第11页  
FM21L16 - 128Kx16 FRAM
Software Write Protect Timing
SRAM Drop-In Replacement
The FM21L16 has been designed to be a drop-in
replacement for standard asynchronous SRAMs. The
device does not require /CE to toggle for each new
address. /CE may remain low indefinitely. While /CE
is low, the device automatically detects address
changes and a new access is begun. This functionality
allows /CE to be grounded as you might with an
SRAM. It also allows page mode operation at speeds
up to 40MHz.
Note that if /CE is tied to ground,
the user must be sure /WE is not low at powerup
or powerdown events. If /CE and /WE are both
low during power cycles, data corruption will
occur. Figure 3 shows a pullup resistor on /WE
which will keep the pin high during power cycles
assuming the MCU/MPU pin tri-states during the
reset condition. The pullup resistor value should
be chosen to ensure the /WE pin tracks V
DD
yet a
high enough value that the current drawn when
/WE is low is not an issue. A 10Kohm resistor
draws 330uA when /WE is low and V
DD
=3.3V.
V
DD
R
MCU/
MPU
FM21L16
CE
WE
OE
A(16:0)
DQ
For applications that require the lowest power
consumption, the /CE signal should be active (low)
only during memory accesses. The FM21L16 draws
supply current while /CE is low, even if addresses and
control signals are static. While /CE is high, the
device draws no more than the maximum standby
current I
SB
.
The FM21L16 is backward compatible with the
1Mbit FM20L08 and 256Kbit FM18L08 devices.
That is, operating the FM21L16 with /CE toggling
low on every address is perfectly acceptable.
The /UB and /LB byte select pins are active for both
read and write cycles. They may be used to allow the
device to be wired as a 256Kx8 memory. The upper
and lower data bytes can be tied together and
controlled with the byte selects. Individual byte
enables or the next higher address line A(17) may be
available from the system processor.
Figure 4. FM21L16 Wired as 256Kx8
Figure 3. Use of Pullup Resistor on /WE
Rev. 1.0
Sept. 2007
Page 7 of 14