MC100EL39
Table 3. MAXIMUM RATINGS
Symbol
Parameter
Condition 1
Condition 2
Rating
Unit
V
V
V
V
PECL Mode Power Supply
NECL Mode Power Supply
V
V
= 0 V
= 0 V
8
CC
EE
I
EE
CC
−8
V
PECL Mode Input Voltage
NECL Mode Input Voltage
V
V
= 0 V
= 0 V
V ≤ V
6
−6
V
V
EE
CC
I
CC
V ≥ V
I
EE
I
I
Output Current
Continuous
Surge
50
100
mA
mA
out
V
Sink/Source
BB
± 0.5
mA
°C
BB
T
Operating Temperature Range
Storage Temperature Range
−40 to +85
−65 to +150
A
T
°C
stg
q
Thermal Resistance (Junction−to−Ambient) 0 lfpm
500 lfpm
SOIC−20
SOIC−20
90
60
°C/W
°C/W
JA
q
Thermal Resistance (Junction−to−Case)
Standard Board
SOIC−20
30 to 35
°C/W
°C
JC
T
sol
Wave Solder
Pb <2 to 3 sec @ 248°C
265
265
Pb−Free <2 to 3 sec @ 260°C
Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the
Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect
device reliability.
Table 4. 100EL SERIES PECL DC CHARACTERISTICS V = 5.0 V; V = 0.0 V (Note 1)
CC
EE
−40°C
25°C
Typ
85°C
Typ
Symbol
Characteristic
Power Supply Current
Min
Typ
50
Max
59
Min
Max
59
Min
Max
61
Unit
mA
mV
mV
mV
mV
V
I
50
54
EE
V
V
V
V
V
V
Output HIGH Voltage (Note 2)
Output LOW Voltage (Note 2)
Input HIGH Voltage (Single−Ended)
Input LOW Voltage (Single−Ended)
Output Voltage Reference
3915
3170
3835
3190
3.62
3995
3305
4120
3445
4120
3525
3.74
3975
3190
3835
3190
3.62
4045
3295
4120
3380
4120
3525
3.74
3975
3190
3835
3190
3.62
4050
3295
4120
3380
4120
3525
3.74
OH
OL
IH
IL
BB
Common Mode Range (Differential)
V
IHCMR
(Note 3)
V
PP
< 500 mV
w 500 mV
1.3
1.5
4.6
4.6
1.2
1.4
4.6
4.6
1.2
1.4
4.6
4.6
PP
V
I
I
Input HIGH Current
Input LOW Current
150
150
150
mA
mA
IH
IL
0.5
0.5
0.5
NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit
board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared
operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification
limit values are applied individually under normal operating conditions and not valid simultaneously.
1. Input and output parameters vary 1:1 with V . V can vary +0.8 V / −0.5 V.
CC
EE
2. Outputs are terminated through a 50 W resistor to V − 2.0 V.
CC
3. V
min varies 1:1 with V , V
max varies 1:1 with V . The V
range is referenced to the most positive side of the differential input
IHCMR
EE IHCMR
CC
IHCMR
signal. Normal operation is obtained if the HIGH level falls within the specified range and the peak-to-peak voltage lies between V min and 1.0 V.
PP
http://onsemi.com
3
ONSEMI [ ONSEMI ]
