Power Management (Continued)
Table 6-2. Power Management Control and Status Registers
Bit
Name
Description
GX_BASE+8500h-8503h
PM_STAT_SMI Register (R/W)
Default Value = xxxxxx00h
31:8
7:3
2
RSVD
RSVD
Reserved — These bits are not used. Do not write to these bits.
Reserved — Set to 0.
SMI_MEM
SMI VGA Emulation Memory — This bit is set high if a SMI was generated for VGA emulation in
response to a VGA memory access. An SMI can be generated on a memory access to one of three
regions in the A0000h-to-BFFFFh range as specified in the BC_XMAP_1 register.
1
0
SMI_IO
SMI VGA Emulation I/O — This bit is set high if a SMI was generated for VGA emulation in
response to an I/O access. An SMI can be generated on a I/O access to one of three regions in the
3B0h-to-3DFh range as specified in the BC_XMAP_1 register.
SMI_PIN
SMI Pin — When set high, this bit indicates that the SMI# input pin has been asserted to the
GXm processor.
Note: These bits are “sticky” bits and can only be cleared with a write of ‘1’ to the respective bit.
GX_BASE+8504h-8507h
PM_CNTRL_TEN Register (R/W)
Default Value = xxxxxx00h
31:8
7:6
5
RSVD
RSVD
Reserved — These bits are not used. Do not write to these bits.
Reserved — Set to 0.
X_TEST (WO)
Transmission Test (Write Only) — Setting this bit causes the GXm processor to immediately trans-
mit the current contents of the serial packet. This bit is write only and is used primarily for test. This
bit returns 0 on a read.
4:3
2
X_FREQ
CPU_RD
CPU_EN
Transmission Frequency — This field indicates the time between serial packet transmissions.
Serial packet transmissions occur at the selected interval only if at least one of the packet bits is set
high: 00 = Disable transmitter; 01 = 1 ms; 10 = 5 ms; 11 = 10 ms.
CPU Activity Read Enable — Setting this bit high enables reporting of CPU Level-1 cache read
misses that are not a result of an instruction fetch. This bit is a don’t-care if the CMEN bit is not set
high
1
CPU Activity Master Enable — Setting this bit high enables reporting of CPU Level-1 cache
misses in bit 6 of the serial transmission packet. When enabled, the CPU Level-1 cache miss activity
is reported on any read (assuming the CREN is set high) or write access excluding misses that
resulted from an instruction fetch.
0
VID_EN
Video Event Enable — Setting this bit high enables video decode events to be reported in bit 0 of
the serial transmission packet. CPU or graphics-pipeline accesses to the graphics memory and dis-
play-controller-register accesses are also reported.
GX_BASE+8508h-850Bh
PM_CNTRL_CSTP Register (R/W)
Default Value = xxxxxx00h
31:8
7:1
0
RSVD
RSVD
Reserved — These bits are not used. Do not write to these bits.
Reserved — Set to 0.
CLK_STP
Clock Stop — This bit configures the GXm processor for Suspend Refresh Mode or 3-Volt Suspend
Mode:
0 = Suspend Refresh Mode. The clocks to the memory and display controller are active.
1 = 3-Volt Suspend Mode. All internal clocks are stopped.
Note: When this register is set high and the Suspend input pin (SUSP#) is asserted, the GXm processor stops all it’s internal clocks,
and asserts the Suspend Acknowledge output pin (SUSPA#). Once SUSPA# is asserted the GXm processor’s SYSCLK input
can be stopped. If this register is cleared, the internal memory-controller and display-controller clocks are not stopped on the
SUSP#/SUSPA# sequence, and the SYSCLK input can not be stopped.
GX_BASE+850Ch-850Fh
PM_SER_PACK Register (R/W)
Default Value = xxxxxx00h
31:8
7
RSVD
Reserved — These bits are not used. Do not write to these bits.
VID_IRQ
Video IRQ — This bit indicates the occurrence of a video vertical sync pulse. This bit is set at the
same timer that the VINT (Vertical Interrupt) bit is set in the DC_TIMING_CFG register. The VINT bit
has a corresponding enable bit (VIEN) in the DC_TIM_CFG register.
6
CPU_ACT
CPU Activity — This bit indicates the occurrence of a level 1 cache miss that was not a result of an
instruction fetch. This bit has a corresponding enable bit in the PM_CNTL_TEN register.
5:2
1
RSVD
Reserved — Set to 0.
USR_DEF
Programmable Address Decode — This bit indicates the occurrence of a programmable memory
address decode. This bit is set based on the values of the PM_BASE register and the PM_MASK
register. The PM_BASE register can be initialized to any address in the full 128 MB address range.
www.national.com
180
Revision 3.1
NSC [ National Semiconductor ]
