■AEC-Q200 Murata Standard Specification and Test Methods
No
13 Thermal Shock
Appearance
AEC-Q200 Test Item
Specifications.
AEC-Q200 Test Method
The measured and observed characteristics shall satisfy the
specifications in the following table.
No marking defects
Solder the capacitor on the test substrate(glass epoxy board).
Perform the 300 cycles according to the two heat treatments listed
in the following table(Maximum transfer time is 20 seconds).
Set for 24+/-2 hours at room temperature, then measure.
Step
1
2
Capacitance
Change
Within +/-10.0%
Temp.(℃） Min.Operating Temp.+0/-3
Max.Operating Temp.+3/-0
Within the specified initial value.
Within the specified initial value.
D.F.
Time
15+/-3
(min.）
15+/-3
Insulation
Resistance
25℃
・ Initial measurement
Perform a heat treatment at 150+0/-10 ℃ for 1hour and then sit
for 24+/-2 hours at room temperature. Perform the initial measurement.
14 ESD
Appearance
Capacitance
D.F.
No marking defects
Per AEC-Q200-002
Voltage setting level : 2kV
Within the specified initial value.
Within the specified initial value.
Within the specified initial value.
Insulation
Resistance
25℃
15 Solderability
95% of the terminations is to be soldered evenly and continuously.
(a) Preheat at 155℃ for 4 hours. After preheating,
ꢀꢀ immerse the capacitor in a solution of rosin ethanol 25(mass)%.
ꢀ Immerse in Sn-3.0Ag-0.5Cu solder solution at 245+/-5℃ or
an eutectic solder solution at 235+/-5℃ for 5+0/-0.5 seconds.
(b) should be placed into steam aging for 8 hours+/-15 minutes.
ꢀꢀ After preheating, immerse the capacitor in a solution of rosin
ꢀ ꢀethanol 25(mass)%.
ꢀ ꢀImmerse in Sn-3.0Ag-0.5Cu solder solution at 245+/-5℃
ꢀ ꢀor an eutectic solder solution at 235+/-5℃ for 5+0/-0.5 seconds.
(c) should be placed into steam aging for 8 hours+/-15 minutes.
ꢀ ꢀAfter preheating, immerse the capacitor in a solution of rosin
ꢀ ꢀethanol 25(mass)%.
ꢀꢀImmerse in Sn-3.0Ag-0.5Cu solder solution or
an eutectic solder solution for 120+/-5 seconds at 260+/-5℃.
16 Electrical
Chatacteri-
zation
Appearance
Capacitance
D.F.
No defects or abnormalities
Shown in Rated value.
0.125 max.
Visual inspection.
The capacitance/D.F. should be measured at 25℃ at the frequency
and voltage shown in the table.
Char
C
6.3V max.
≦10F
10V min.
10F < C
Item.
Frequency
Voltage
1.0+/-0.1kHz
0.5+/-0.1Vrms
1.0+/-0.1kHz
1.0+/-0.2Vrms
120+/-24Hz
0.5+/-0.1Vrms
Insulation
Resistance
25℃
More than 1000MΩ or 50Ω ∙ F (Whichever is smaller)
More than 100MΩ or 5Ω ∙ F (Whichever is smaller)
The insulation resistance should be measured with a DC voltage not
exceeding the rated voltage at 25℃ and maximum operating temperature
within 1minute of charging.
Insulation
Resistance
85℃(For R6)
105℃(For C8)
Dielectric
Strength
The charge/discharge current is less than 50mA.
No failure
No failure should be observed when 250% of the rated voltage is
applied between the terminations for 1 second to 5 seconds.
The charge/discharge current is less than 50mA.
JEMCGS-01744N
4
MURATA [ muRata ]
