64Mb: x4, x8, x16 SDRAM
Pin and Ball Assignments and Descriptions
Table 4: Pin and Ball Descriptions
Symbol
Type Description
CLK
Input Clock: CLK is driven by the system clock. All SDRAM input signals are sampled on the positive
edge of CLK. CLK also increments the internal burst counter and controls the output registers.
CKE
Input Clock enable: CKE activates (HIGH) and deactivates (LOW) the CLK signal. Deactivating the
clock provides precharge power-down and SELF REFRESH operation (all banks idle), active
power-down (row active in any bank), or CLOCK SUSPEND operation (burst/access in pro-
gress). CKE is synchronous except after the device enters power-down and self refresh modes,
where CKE becomes asynchronous until after exiting the same mode. The input buffers, in-
cluding CLK, are disabled during power-down and self refresh modes, providing low standby
power. CKE may be tied HIGH.
CS#
Input Chip select: CS# enables (registered LOW) and disables (registered HIGH) the command de-
coder. All commands are masked when CS# is registered HIGH, but READ/WRITE bursts already
in progress will continue, and DQM operation will retain its DQ mask capability while CS# is
HIGH. CS# provides for external bank selection on systems with multiple banks. CS# is consid-
ered part of the command code.
CAS#, RAS#,
WE#
Input Command inputs: RAS#, CAS#, and WE# (along with CS#) define the command being en-
tered.
x4, x8:
DQM
Input Input/output mask: DQM is sampled HIGH and is an input mask signal for write accesses and
an output enable signal for read accesses. Input data is masked during a WRITE cycle. The
output buffers are High-Z (two-clock latency) during a READ cycle. On the x4 and x8, DQML
(pin 15) is NC; DQMH is DQM. On the x16, DQML corresponds to DQ[7:0] and DQMH corre-
sponds to DQ[15:8]. DQML and DQMH are considered same-state when referenced as DQM.
x16:
DQML, DQMH
BA[1:0]
A[11:0]
Input Bank address input(s): BA[1:0] define to which bank the ACTIVE, READ, WRITE, or PRE-
CHARGE command is being applied.
Input Address inputs: A[11:0] are sampled during the ACTIVE command (row address A[11:0]) and
READ or WRITE command (column address A[9:0] for x4; A[8:0] for x8; A[7:0] for x16; with
A10 defining auto precharge) to select one location out of the memory array in the respective
bank. A10 is sampled during a PRECHARGE command to determine whether all banks are to
be precharged (A10 HIGH) or bank selected by BA[1:0] (A1 LOW). The address inputs also pro-
vide the op-code during a LOAD MODE REGISTER command.
x16:
DQ[15:0]
I/O
I/O
I/O
Data input/output: Data bus for x16 (pins 4, 7, 10, 13, 42, 45, 48, and 51 are NC for x8; and
pins 2, 4, 7, 8, 10, 13, 42, 45, 47, 48, 51, and 53 are NC for x4).
x8:
DQ[7:0]
Data input/output: Data bus for x8 (pins 2, 8, 47, 53 are NC for x4).
Data input/output: Data bus for x4.
x4:
DQ[3:0]
VDDQ
VSSQ
VDD
VSS
Supply DQ power: DQ power to the die for improved noise immunity.
Supply DQ ground: DQ ground to the die for improved noise immunity.
Supply Power supply: 3.3V ±0.3V.
Supply Ground.
NC
–
No connect: These should be left unconnected.
PDF: 09005aef80725c0b
64mb_x4x8x16_sdram.pdf - Rev. U 05/13 EN
Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 1999 Micron Technology, Inc. All rights reserved.
13