欢迎访问ic37.com |
会员登录 免费注册
发布采购

PIC18F25J10-I/SS 参数 Datasheet PDF下载

PIC18F25J10-I/SS图片预览
型号: PIC18F25J10-I/SS
PDF下载: 下载PDF文件 查看货源
内容描述: 28 /40/ 44引脚高性能, RISC微控制器 [28/40/44-Pin High-Performance, RISC Microcontrollers]
分类和应用: 微控制器和处理器外围集成电路光电二极管PC时钟
文件页数/大小: 368 页 / 5652 K
品牌: MICROCHIP [ MICROCHIP ]
 浏览型号PIC18F25J10-I/SS的Datasheet PDF文件第173页浏览型号PIC18F25J10-I/SS的Datasheet PDF文件第174页浏览型号PIC18F25J10-I/SS的Datasheet PDF文件第175页浏览型号PIC18F25J10-I/SS的Datasheet PDF文件第176页浏览型号PIC18F25J10-I/SS的Datasheet PDF文件第178页浏览型号PIC18F25J10-I/SS的Datasheet PDF文件第179页浏览型号PIC18F25J10-I/SS的Datasheet PDF文件第180页浏览型号PIC18F25J10-I/SS的Datasheet PDF文件第181页  
PIC18F45J10 FAMILY  
If the general call address matches, the SSPxSR is  
transferred to the SSPxBUF, the BF flag bit is set  
(eighth bit) and on the falling edge of the ninth bit (ACK  
bit), the SSPxIF interrupt flag bit is set.  
16.4.5  
GENERAL CALL ADDRESS  
SUPPORT  
The addressing procedure for the I2C bus is such that  
the first byte after the Start condition usually  
determines which device will be the slave addressed by  
the master. The exception is the general call address  
which can address all devices. When this address is  
used, all devices should, in theory, respond with an  
Acknowledge.  
When the interrupt is serviced, the source for the  
interrupt can be checked by reading the contents of the  
SSPxBUF. The value can be used to determine if the  
address was device-specific or a general call address.  
In 10-bit mode, the SSPxADD is required to be updated  
for the second half of the address to match and the UA  
bit is set (SSPxSTAT<1>). If the general call address is  
sampled when the GCEN bit is set, while the slave is  
configured in 10-Bit Addressing mode, then the second  
half of the address is not necessary, the UA bit will not  
be set and the slave will begin receiving data after the  
Acknowledge (Figure 16-15).  
The general call address is one of eight addresses  
reserved for specific purposes by the I2C protocol. It  
consists of all ‘0’s with R/W = 0.  
The general call address is recognized when the  
General Call Enable bit, GCEN, is enabled  
(SSPxCON2<7> set). Following a Start bit detect, 8 bits  
are shifted into the SSPxSR and the address is  
compared against the SSPxADD. It is also compared to  
the general call address and fixed in hardware.  
FIGURE 16-15:  
SLAVE MODE GENERAL CALL ADDRESS SEQUENCE  
(7 OR 10-BIT ADDRESSING MODE)  
Address is compared to General Call Address  
after ACK, set interrupt  
Receiving Data  
ACK  
R/W = 0  
ACK D7 D6  
General Call Address  
SDAx  
SCLx  
D5 D4 D3 D2 D1 D0  
1
2
3
4
5
6
7
8
9
1
2
3
4
5
6
7
8
9
S
SSPxIF  
BF (SSPxSTAT<0>)  
Cleared in software  
SSPxBUF is read  
SSPOV (SSPxCON1<6>)  
GCEN (SSPxCON2<7>)  
0’  
1’  
© 2009 Microchip Technology Inc.  
DS39682E-page 175  
 复制成功!