欢迎访问ic37.com |
会员登录 免费注册
发布采购

PIC18C452-I/L 参数 Datasheet PDF下载

PIC18C452-I/L图片预览
型号: PIC18C452-I/L
PDF下载: 下载PDF文件 查看货源
内容描述: 高性能微控制器,10位A / D [High-Performance Microcontrollers with 10-Bit A/D]
分类和应用: 微控制器
文件页数/大小: 296 页 / 4835 K
品牌: MICROCHIP [ MICROCHIP ]
 浏览型号PIC18C452-I/L的Datasheet PDF文件第93页浏览型号PIC18C452-I/L的Datasheet PDF文件第94页浏览型号PIC18C452-I/L的Datasheet PDF文件第95页浏览型号PIC18C452-I/L的Datasheet PDF文件第96页浏览型号PIC18C452-I/L的Datasheet PDF文件第98页浏览型号PIC18C452-I/L的Datasheet PDF文件第99页浏览型号PIC18C452-I/L的Datasheet PDF文件第100页浏览型号PIC18C452-I/L的Datasheet PDF文件第101页  
PIC18CXX2  
Figure 10-1 is a simplified block diagram of the Timer1  
module.  
10.0 TIMER1 MODULE  
The Timer1 module timer/counter has the following fea-  
tures:  
Register 10-1 shows the Timer1 control register. This  
register controls the operating mode of the Timer1  
module as well as contains the Timer1 oscillator enable  
bit (T1OSCEN). Timer1 can be enabled/disabled by  
setting/clearing control bit TMR1ON (T1CON<0>).  
• 16-bit timer/counter  
(Two 8-bit registers; TMR1H and TMR1L)  
• Readable and writable (Both registers)  
• Internal or external clock select  
• Interrupt on overflow from FFFFh to 0000h  
• Reset from CCP module special event trigger  
Register 10-1: T1CON: Timer1 Control Register  
R/W-0  
RD16  
U-0  
R/W-0  
R/W-0  
R/W-0  
R/W-0  
R/W-0  
R/W-0  
T1CKPS1 T1CKPS0 T1OSCEN T1SYNC TMR1CS TMR1ON  
bit 0  
bit 7  
bit 7  
RD16: 16-bit Read/Write Mode Enable bit  
1= Enables register Read/Write of TImer1 in one 16-bit operation  
0= Enables register Read/Write of Timer1 in two 8-bit operations  
bit 6  
Unimplemented: Read as '0'  
bit 5:4  
T1CKPS1:T1CKPS0: Timer1 Input Clock Prescale Select bits  
11= 1:8 Prescale value  
10= 1:4 Prescale value  
01= 1:2 Prescale value  
00= 1:1 Prescale value  
bit 3  
bit 2  
T1OSCEN: Timer1 Oscillator Enable bit  
1= Timer1 Oscillator is enabled  
0= Timer1 Oscillator is shut off.  
The oscillator inverter and feedback resistor are turned off to eliminate power drain  
T1SYNC: Timer1 External Clock Input Synchronization Select bit  
When TMR1CS = 1:  
1= Do not synchronize external clock input  
0= Synchronize external clock input  
When TMR1CS = 0:  
This bit is ignored. Timer1 uses the internal clock when TMR1CS = 0.  
TMR1CS: Timer1 Clock Source Select bit  
bit 1  
bit 0  
1= External clock from pin RC0/T1OSO/T13CKI (on the rising edge)  
0= Internal clock (FOSC/4)  
TMR1ON: Timer1 On bit  
1= Enables Timer1  
0= Stops Timer1  
Legend:  
R = Readable bit  
W = Writable bit  
’1’ = Bit is set  
U = Unimplemented bit, read as ‘0’  
’0’ = Bit is cleared x = Bit is unknown  
- n = Value at POR reset  
7/99 Microchip Technology Inc.  
Preliminary  
DS39026B-page 97  
 复制成功!